Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
I am trying to make the nrf52832 enter in ON/low power mode for inactivity periode.
I must have the "System ON, No RAM retention, Wake on RTC" as indicated in nrf52832 datasheet...
Hi,
I run the Secure DFU, and I'm doing OTA update without any issue.
The problem is the case that I'm doing an OTA update with a application-version smaller than...
Hi all, Nordic distributors no longer carry the nRF52840-PDK, which included the NFC antenna. What is a direct replacement for the Nordic NFC antenna that used to be included...
I am trying to connect a BerryMed MD1000 Pulse Oximeter (BLE Server) with an Adafruit Bluefruit Feather (nRF52-enabled) Arduino board (BLE Client).
I made an Arduino sketch...
hi All!
I use WAKE UP event from G-SENSOR on some GPIO to wake up the MCU on motion detected.
But sometimes ( ~1% ) the event does not occur for unknown reason until RESET...
Hi,
I want to have 2 SPI slaves on the same bus.
I saw in other posts that in the past it was not supported by the spi driver and that i should use NRF_DRV_SPI_PIN_NOT_USED...
What will be the real time effect if we give high value to Tx rather than keeping default Tx value as '0' ? Will it increase signal range?
Regards,
Ashiq Mohammed
I need nRF connect & toolbox on my iphone to do evaluation.
There is nRF toolbox, nRF Beacons but no nRF connet in App store.
Where can I find nRF connect ?
thanks ...
Hi.
Why longer advertising data destroy device ?
When I set length of advertising data to 20bytes in advertising_init(), device will crash and I can't download new firmware...
Hello,
The sd_softdevice_enable returns 8 (captured with my jlink probe), how can I investigate please ?
Configuration:
SDK 15.0.0, SD_132_6.0.0 with bootloader
In my application, I use the peer manager that has called the fds_init function, should I call it again if I want to use the fds to store my data. Will the peer manager use...
Hello Everyone,
I am using Nordic's Power Profiler Kit to estimate the current consumption of an external board. I have been able to configure it properly and getting results...
On nrf52840 I get a current of ~10 uA while sleeping. At the moment I don't run any code and don't start up the softdevice. I go directly to sleep with __WFE(). The result...
Hi All!
Faced with big problem with SCANNING procedure (nRF52840)
We have a BLE network : one CENTRAL and up to 6 PERIPHERALs can be connected simultaneously to the CENTRAL...
