Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
I get the following error when launching the app, and the "Start scan" button either doesn't do anything or can't be clicked.
Error while probing devices: Error occured...
Hi
I am measuring the current consumption (with an amperemeter) of the nRF52 on the PCA10056 Devboard. The nRF52840 is supplied directly by connecting the external power...
Hi,
I have a problem when I do a write request on a 20 bytes characteristic from a custom service.
The funtion sd_ble_gattc_write return error 0x7 but I can't find what...
I want to stream a mono audio signal with high bandwidth (20kHz) from a remote device to a base device.
Need to A2D signal on remote and D2A the signal on the base. Low...
Hi,
The SEGGER have released a JLink software version that support to use JLink on ARM Linux platform。
I try it on raspberry pi, and it work well. But when i use pynrfjprog...
Hello.
I have a project that use the NRF_LOG_INFO for printing messages, and it is work O.K.
Now I add a part that need also to get parameters from the terminal.
I can...
Hi
Please advise when I can find firmware for nRF52840-DK which can send advertising packets or any data packets at data rate 125Kbps and +8dBm output power
I have two...
Hallo Everyone
We have developed a firmware for our systems using the nRF52832 with BLE 4.0.
Now we need to move to BLE 5.0. As far as I know the nRF52832 works with...
I get a strange error message reading from my hdc 1080 temp/rh sensor:
[00:08:38.013,916] <err> i2c_nrfx_twim: Error 195952641 occurred for message 0
I csnnot find any...
Hello Everyone,
I am working with nRF52832 chip on our custom board. I am using SDK 14.2 and SD v5.0.0 for development on a windows platform with Segger ES.
I am looking...
Hello all, I'm using nRF52 DK.
I'm going to use this DK as a master of BLE, and send information which is from BLE peripheral device to another board using SPI.
Anyway...
I am trying to implement the MAX30105 pulse oximeter sensor along with the Nordic Thingy 52 application source.
I referred the sample ADXL375 code provided by Simon here...
Hi,
I got some issues with migrating from SDK 14.0.0 to SDK 15.3.0 on a project that was developped from the previous developper. I have already done a lot of migration...
