Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hello developers,
I am developing a smart padlock using nRF52832 SoC and plan to launch it on kickstarter. By far I have successfully made prototypes using HRM code as...
Hello everyone, I've been trying to solve this problem for several days.
Hello everyone, I've been trying to solve this problem for several days.
I have developed a custom...
Hello!
I make peripherial device with some custom services. It is connecting with smartphone. i need secure access with it with passkey (pin code).
My last result is when...
I have one Service UUID and its only two characteristics UUID which is Tx (App to BLE) and Rx(BLE device to APP) to get different type of data e.g. Heart rate, Sleep data...
Thanks for your help עוטד. I want to use BLE / beacon technology in order to track items that pass-by in high-speed and close proximity (0.5m). This means I only have a few...
Hi,
I am using ble_app_hrs_c as the base for central. I have included 5 characteristics in the peripheral and central side. How to make ble_nus_c_rx_notif_enable() to notify...
ble_gap.h Hi,
At the moment, when a link loss is detected (in a connected mode), it takes around 3 seconds for it to be identified (with DISCONNECTED event). Is there a way...
Hi,
We are using system-off mode to save power in our device which uses nrf51822 chip. Our application requires regular wake-ups using RTC interrupts.
But the wake up...
Hello!
I know that nrf51822 beacon advertising packet consists of the following seven data fields:
Vendor ID
Service
Data payload size in bytes
UUID – manufacturer...
I would like to develop a BLE keyboard using nRF52832.
If you know the example source code, please let me know.
And can USB BLE Dongle for Desk-Top PC use the following...
Hi team,
I am trying to figure out how mesh network works. I do experiment with nrf52832 develop board and nrf5_SDK_for_Mesh_v0.9.2-Alpha. After I flashed light_control_server...
I have an app that requires BLE stack to be re-initialized, however it seems that if you run
ble_dfu_init();
more than once, it crashes
Upon further inspection...
Hi all,
I'm working with the nRF52 and I'm trying to run the heart rate sensor example from SDK version 13.1.0 using Crossworks as my IDE. I can compile and run the program...
Hi,
The below results indicate the nRF Connect app requires a handshake even when scanning without connecting. Is this true?
I am using the android 'nRF Connnect' app...
