Hi we are using Nordic 54280 .dk
Thanks for your immediate response.
im facing few practical issue with hardware interface.
1.what are the procedure to power up...
Hi,
I would like to test a websocket connect over NB-IOT with the nRF9151DK. I started with the https_client example to do an https handshake with the server and then add...
I have a 7002dk dev kit. Currently for evaluating the nrf5340, which will be used in my product. Currently i am trying to evaluate if it is possible to use the nRF5340 USB...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
I have compiled code that debugs and runs normally on the nRF52840DK. I just connected my custom PCB to the debug out connector on the DK and I have two issues that are probably...
Hi,
I have designed a custom board using the nRF52840 and have successfully programmed it using SWD (SWDIO & SWDCLK) with a J-Link programmer . However, I now want to program...
Dear Nordic
I'm looking for a DTM code for nRF54L15,
From previous experience of nRF52,
There are some example HEX files available in SDK,
But I can't find any example...
Dear Nordic,
I have managed to modify the HID Keyboard demo (SDK10/nRF51 DK) to have both keyboard and consumer control functions. Works fine on Android, however it shows...
How should the addressing be between an nrf24LU1+(transmitter) and nrf24l01+(Reciever) in the code.?
The registers TX_ADDR, RX_ADDR_P0, RX_ADDR_P1 are updated on a device...
Do we need to explicitly set the ENABLE field (Bit31) of RADIO->OVERRIDE4 when applying the override values from FICR->BLE_1MBIT[n]?
From the few samples I've checked,...
Please teach me the minimum theoretical value of the transmission time in the following conditions.
CPU --> nRF24L01 --(2.4GHz/1Mbps)--> nRF24L01 --> CPU
CPU -->...
I need to send a long (let's say 10Kb) notification from Bluez 5.37 on my Linux device to a mobile phone.
My implementation is based on src/shared/gatt-server.c .
I...
Hi,
I have put in my chip (nrf51422):
-1 softDevice s110 8.0.0;
-2 application (hrm_whit_dfu);
My problem is:
when i send characteristic to start advertising the board...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
