I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello everyone
i am trying to set the password for connection whenever its start advertsing but the static passkey option will set the pssword only for bonding not for...
Hi.
I am using nRF24, nRF51, and nRF52 chips.
Today I saw nRF31562A on some device(wireless mouse of Logitech)
However I can't find any information about this chip,
even...
Hello,
I would appreciate if you could help me solve what i am trying to do. I have nrf51DK board with nrf51422 on it, PCA10028, S130 and i want to use to scan for another...
Hello,
I am working on SDK 9.0 and softdevice 8.0 and the requirement for my application is the device has to advertise till it gets connected and even after disconnection...
Dear all,
I get a new nRF51-DK and I am trying to download an hex file into it.
I downloaded and installed nRFgo studio.
I connected my nRF51-DK to my...
Hi. I've gone through a lot of documentation and can't seem to find if this is documented by Nordic semi.. please answer if you know, or can point me to experiments/documentations...
I soldered 5 pieces of PCBA with nRF51822, but I got only one PCBA which can connect to J-LINK. I checked the bad four and found that SWDIO of nRF51822 on the four board is...
I'm having a weird hardfault and, I can't make sense of it.
Here's what I do know:
nrf sdk 9.0.0;
nrf51422 on a dk;
I have RTC1, SPI0, and TWI1 enabled (also a uart for...
Hello,
call of app_pwm_init() function forces logic 1 on PWM enabled pin after advertising timeout expires. Why? It causes my LED to turn completely on after advertising...
Hello,
In my code I would like to switch between BLE advertising and listening nearby devices (and save their RSSI) in the same code. After each advertising period, I would...
i have use nrf51822 and android app(nRFuart)
i was masure currunt through DSO but i think its not accurate...
i can't masure exect(high accurate) currunt consumption in...
I read through the following post and still couldn't get debug info out.
I have tried the settings there and from another post with no luck. I'm using putty on a win 8...
Hello everyone,
I am trying to enable notification on a characteristic based on the code example from nAN36.
Unfortunately the sd_ble_gatts_hvx() function returns:
...
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I desperatly try to implement a bootloader with the s310 softdevice. When I received the data to be written (via BLE), I erase the flash:
std::uint32_t rc = NRF_ERROR_BUSY;...
