Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
I am attempting to stream data in chunks of 65535 bytes from the nRF9160 using data mode from the 2.6.1 version of serial_lte_modem sample code. The nRF9160 receives AT commands...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
Hi,
I realise this is now quite an old version of the SDK and this particular library is no longer supported, but we have not yet migrated our project (I did try once...
I'm using the nordic ppk II to measure the power consumption of my device.
In order to validate the charge (current integral) displayed by the PPK2 i put two PPK2 daisy...
I have not messed around with devicetree much before this point. I'm trying to create a custom dts and bindings for my device. Within my custom dts file, I reference the nRF52833...
I am working with nRF52840 with MAX86141 and learning how to setup the SPI connection
Here is an opensource example : https://github.com/JON95Git/zephyr-spi-directly
And...
Hi Support Team,
I am using the nRF7002DK board for our product POC (Proof of Concept) purposes. We plan to use the same MCU, the nRF5340, for our final product.
I have...
Hello,
I am using an nRF9160dk with the nRF52840 acting as the BT controller running the Bluetooth: HCI low power UART sample ( https://developer.nordicsemi.com/nRF_Connect_SDK...
modem_info_get_current_band expects an uint8 pointer to store the band into, but scans for an unsigned int (probably above 8 bit) in nrf_modem_at_scanf. This leads to memory...
Hello
I am working on a WiFi application using a custom board equipped with both the nRF5340 aswell as the nRF7002. When requesting a WiFi connection using the net_mgmt...
I'm using 2 nRF52840 DK to run a data transfer test between a central and a peripheral.
The Central device uses ble_app_uart_c, The peripheral uses ble_app_uart. These examples...
We are trying to re-layout the PCA10059 Dongle. I would like to continue to use the existing USB bootloader .hex file for updates via CDC_ACM. One thing I am confused about...
Hello, DECT NR+ seems as a good fit for our product, however, current stack providers(Wirepass and Lynq) are not suitable for us. I'm wondering are there other companies who...
I am trying to test a nRF5340 with a 1.3 inch waveshare 240x240 display using a st7789 driver. How would I connect the display to the board:
VCC
3.3v
...
Hi i am currently using nrf52840 s140 sdk ver 17.1.10 using central uart and i need to add dfu ota code to it how can i add what is the required files to it we tried these...
Since the tickets are scattered, I will summarize the questions about nRF5340 Audio again.
Prerequisites
NCS version is 2.5.0. Raytac's MDBT53-1M is implemented on a homemade...
Hi Team,
We are using SLM SDK 2.4.0 and MFW 1.3.5
We moving forward to SLM SDK 2.5.2 and want to FOTA all our products outside, but, some have problems with cellular...
I'm organizing my code with nRF SDK v17.0.0,using the board nRF52832 that designed by myself.
In order to support multi-central,the peer_manager module is used.So that I...