Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
I need a battery-powered programmable device to communicate via Bluetooth to a headset, and communicate with another device via serial (TXD/RXD) interface. Performance requirements...
Hello,
I am writing a single byte value to a cypress module using write with response (BLE_GATT_OP_WRITE_REQ). For some reason the peripheral will receive the value but...
Hi!
I am trying to develop a way for a Bluetooth Central and Bluetooth Peripheral using Secure Connections (security mode 1 level 2 if I'm not mistaken) using a static...
Dear nRF,
I have couple of nRF21540-dk boards (PCA10112) in my hand. I would like to use nRF Connect Direct Test Mode to activate TX and RX.
I found that the tool lacks...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
I am taking over a firmware Bluetooth project and am reading the code that is having some issues. Below is a snippet from a BLE characteristic read callback. Here a double...
I set a timer on the net core of nrf5340. The timer sets an interrupt of 10s. After the chip is reset and runs for 10s, the while (1) of the main function is interrupted,...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
If I add CONFIG_LOG=y to "prj.conf" in the zephyr sample peripheral_dis, when...
Hello,
I'm working with a NRF52840 DK and a module BLE nrf805.
I'm programming thanks to the software SEGGER.
I have sent the blinky simple in my dev kit to test a...
Hello,
I am using the Segger Embeddd Studio from the nRF Connect Desktop and the nRF52840-DK board.
I am working over the project into the "ses" directory for SoftDevice...
Hi,
Do you have an example of the \ble_peripheral\ble_app_hrs with Coded PHY for the nRF5_SDK_17.1.0? I have tried to use the BLE_GAP_PHY_CODED definition in different places...
Hi,
Is it any possible setup to connect a NRF52840-DK to the nRF Connect app in a smartphone without pairing or bonding? That would help me for testing and in this stage...
Hello
I am launching a project and I intend to:
Want to use multiple mobile phones and nrf-mesh software, Connect to a mesh server and turn on or off a led
So I connect...
