Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
We have a product that uses a module containing NR52832 and also both 32kHz and 32MHz crystals. This has been operating correctly and is in full scale production.
On our...
Hi,
I'm having some difficulty debugging an issue with the mqtt library on the nrf9160dk.
I have written my own Cmqtt library class that wraps the Zephyr mqtt library...
Dear ,
On Windows 10 Bluetooth add a device,
Why SDK_17_0_2 Example does Bluetooth be disconnect immediately after pairing
(Use about \nRF5_SDK_17_0_2\examples\ble_peripheral...
When I open the Light Bulb project in Segger Embedded Studio I see a bewildering list of project items. I pick the first project, 'zephyr/merged.hex' and right click to set...
SDK: 4.1.0
CHIP: 52840
Hi, I have developed sleepy zed. It lost the connection with the network after joining in 1~3 days.
It assumes that the zed couldn't get the...
Hi, guys.
I'm using nRF52 DK (PCA10040). After I used Zadig (Driver setup for J-link), I cannot build and run my previous code to the nRF52 DK anymore (see the first 3 images...
Hi
I am using nrf52840 boards and by using the coexist program I am able to send and receive messages through mesh while using the ble services.
I followed the instruction...
I use NRF52DK as central device I also use a SDK that is ble_app_uart_c code for my project. and i would like to take my peripheral devices whice are phone or PC their RSSI...
Hello - we're using "nRF Connect" from the Apple App Store for the development of our project.
First, thank you for making this tool available and free for everyone to use...
I am using nrf52840 via NRF Connect and Zephyr configured to use the Nordic SoftDevice BLE controller.
My use case is for a central to sample a rapidly changing real-time...
As a beginner,I’m sorry for asking such a stupid question,but it has annoyed me for a long time.
I built and downloaded the program to my DK,and I used PuTTY to connect...
Hello,
I've designed a pcb using the 52840 chip which is essentially identical to the dongle design. My intent was to use the firmware that comes pre-installed with the...
Is there a set of prj.conf settings that I can use to redirect the AT command interface to the RTT debugger? Would be nice not to have to hook up a serial connection.
Hi All,
as the title say I'd like to know if is the Wake on GPIO available for nRF52840_dongle and what is the I OFF_RAMOFF_GPIO ?
My application should behave more or...
Hello. I'm developing a project using nRF52840. I've been working with the nRF52840Dev Board and I have a BLE project that runs there. I'm developing in Segger IDE and using...
