Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello all,
I am working on the DFU on the NRF52810 custom board
I am trying with secure bootloader example PCA10040e
with sdk 15.3 s112_nrf52_6.1.1 softdevice
Then...
Central and Peripheral are connected by BLE.
The following error may be displayed when sending BLE message multiple times to the peripheral at the same time.
>> NRF_ERROR_RESOURCES...
Hi,
I found a bug in fds module ( Flash Data Storage ) which lead to data system corruption.
Scenario:
Given the device started GC(Garbage Collection) procedure...
Hi,
I have found a bug in the fds module (Flash Data Storage), which lead to losing "installed pages". If it was a swap page, fds module will be bricked.
Tested on SDK...
Hi,
I have written a short driver for the ADXL362 accelerometer, which I'm attaching here, and I've connected breakout board of the accelerometer from Sparkfun to the nRF51...
Hi there,
I have just upgraded the SES to V4.16 and followed the assistant guide in nRF Connect. I have deleted the old ncs folder (and all files) and also created a new...
I measure 184 uA of current during WFE. I've read in other posts that the nRF52832 should draw about 1.2 uA during WFE.
I've looked over the project settings many times...
Greetings,
I am using nRF52840 Dongle and nRF Connect v3.2.0 PC application to scan for nearby Bluetooth devices and connect to them.
I want to develop a PC application...
Hi, I use in my design a component which use the nRF52840 - WLCSP package.
I use SPI to connect the nRF to a SD card slot. With the package, I understand that pin K4 (P0...
Hi all,
I am debugging the data transition flow of the Node with Relay.
We modified the example of ONOFF_server. We found that the unicast address should the odd number...
Hi, I cannot find my Nordic Thingy91 as a USB connected device in the nRFConnect desktop application.
I tried to connect the Thingy via a JTAG 10-pin cable via an external...
Hi,
Greetings!
I am trying test DFU example for nRF52832 and I need help to move ahead.
Setup:
nRF52832 SDK for Mesh V3.1.0
nRFSDK V15.3.0
nRF52832 Development...
Dear all,
I just played around with the nRF Sniffer and I am pretty impressed. Really good tool and most of the packets are received.
I want to build an application where...
I have reprogrammed the nRF52840 board controller. When I run the lte_ble_gateway application I get the following on the 2nd dev kit VCP port:
SPM: NS image at 0xc000...
hello, i have a question, i use sdk15.3 for nRF52832, i run for example flash_fds, sometimes it will not be able to erase or write to memory, after restarting the device,...
