Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I am testing out the Bluetooth Mesh SDK 0.9.1 Alpha using the light control client/server example. The examples have not been modified.
I have set up a nRF52 development...
In android while at the stage of scanning there is list of ssid ,i am getting print of scan_result but while trying to print the RSSI value,the result is 0 .Files i have changes...
With our custom board, I have implemented the battery service and it's working well. But the nus service is not shown up at all, the same initialization code as the official...
i use the nrf52832,s uarte. using the app_uart_fifo.c document. but i can only receive the max 256 bytes.the configuration is belows:
APP_UART_FIFO_INIT(&comm_params,
...
Hello,
Is the characteristic value data supplied to sd_ble_gatts_characteristic_add() and sd_ble_gatts_value_set() copied into the softdevice RAM, or does the softdevice...
.pdf d051cefddbc197cd7d)
Hello All,
I am working on Automotive project using nrf51824 SOC...
Hi,
I am working on making a test harness using the nRF52DK and a raspberry pi so I may run unit tests directly on the nRF52832. I want to use the UART to give test results...
We recently did pre-compliance RF radiated immunity testing at a certified lab. The EUT was nRF52832 on a battery powered post card sized circuit board with some sensors....
when I run the program I get this error
Checking installed packages
pyside: 1.2.2
pyqtgraph: 0.10.0
numpy: 1.11.3
pynrfjprog: 9.1.0
Warning: The software is tested...
I am using a PPK with v1.0.0, but elsewhere in DevZone I see references to later versions of the software. Where can I download the later versions from? Have I missed a link...
Hi.
Great that you have added logging capability to the PPK desktop app. This was exactly what I needed.
I noticed one minor issue with the logging: When starting logging...
I have an application with hard real-time requirements (i.e. down to the clock cycle). My topology and desired timeline can be seen below. Concerning the timeline, I believe...
Hello,
I have a question regarding app interrupt handling.
When an Application Timer Interrupt is being handled, can it preempted by a higher prioritized interrupt of...
Hi,
I have used this antenna for my nRF51 layout, but it seems that the device is using very high currents! like in order of 200mA, I just wanted to know if this is because...
I am using below code to send data over nus. If the data size is 150 bytes, it is OK. However, if the data size is 200 bytes, the nRF51822 will reset. Please tell me how to...
