Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi are there any image/bulk data transfer demo to test throughput between nRF and iOS application
There is one for older nRF5 SDK but couldn't find one for nRF connect ...
Hi,
I use two nRF52833-DK boards for uart communication (both using pin p0.06 for TX and p0.08 for RX), with their TX and RX and GND pins connected to each other, and perform...
Hello
I am facing issues while pairing nRF7002DK with nRF WiFi provisioner app, when I build the app (provided by nordic and hosted on github). However the pairing is successful...
Hello. On july 26 at the same hour, about 30 of our cellular modems stopped sending data. They are all using Verizon firmware. The units using Hologram firmware are still...
Hi
I have 2 BLE boards with some environment sensors on them.
I need to synchronise the 2 boards with < 1 mili second precision.
one board is configured as central,...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hello,
We are using Zephyr OS and SDK v2.5.0 on nrf52840 chip. We have noticed some delay between spi_write and spi_read of 29µs,which is critical for our goal. Comparing...
After I installed nRF Connect SDK 2.7 and tried to run the pre-release version of VS Code extension, I am now compleatly unable to make nRF Connect for VS Code function. ...
I' m using custom board of nrf5340 with nrf7002, and the SDK version is ncs v2.5.2.
I've tried to build and run, but the log in RTT viewer is only print the line "Bringing...
Hi nordic:
I am currently using NRF52833 to create a MESH product and would like Bluetooth to send AOA tag information in MESH mode. Is this feasible?
Best Regards ...
I encountered the following error while building my ZigBee app on a CI (dockerized Linux container), after bumping the SDK from 2.6.1 to 2.7.0.
The part "nRF52840" in...
Hi All, I am using an nrf52832 and using NCS version 2.6.0. I am having an issue where I am trying to initialize and run a thread, but the thread never runs. I have tried...
I want to set the CONFIG_CAF_BLE_ADV_FAST_ADV Kconfig option to make the Peripheral initially advertise with a shorter interval,but after adding some dependency configurations...
hello.
Currently I am implementing BLE Multi advertising in
NCS SDK: version 2.6.0.
I have a question during development through the samples/bluetooth/multiple_adv_sets...
Hello,
I am working with the USB CDC ACM Sample Application from NCS V2.1.0 on nRF52840DK and have encountered an issue when attempting to replace the UART_INTERRUPT_DRIVEN...