Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
Greetings, Our system consists of three BLE sensors using an nRF52840 to send data back to a central tablet or PC. We are receiving reports that the sensors take a long time...
I've been searching threads on this topic on DevZone and I found a couple that concluded that MCUBoot can work with external SPI flashes, but not with an SD card.
Is that...
I am using PHYTEC link board eth ( https://docs.zephyrproject.org/latest/boards/shields/link_board_eth/doc/index.html ) as ethernet shield using SPI on nRF9161.
I updated...
Hello, per the PPK2 user guide, I see that the switching during auto-ranging can cause measured current to be higher than the actual current due to inductance.
To be clear...
Our products use NRF52832 chips in production, and now the finished product needs to do an SRRC certification, but I need to confirm whether the original factory of this chip...
Hey, I need to set characteristic length for a PTS test to MTU-1 Otherwise the test case GATT/SR/GAC/BV-01-C will failed with the message - Failed: Cannot find characteristic...
hello:
My project is based on "esb_rx",NCS2.5.1，nRF52832.I need a Unique address for my product ,so I add flash read/write function for my projict, base on "soc_flash_nrf...
Hi,
we are facing an issue of loading the application written with nRF Connect SDK to the nRF52840 which has nRF5 SDK's secure bootloader. Update process should be performed...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
Hello,
This demo gives me automatic pairing and password input.
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-problems-between-ble_peripheral-and-ble_central...
