Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I made all of the functions using nrf52832, s132. Now I want to reduce the current consumption.
So, I tried changing the slave latency. It was confirmed that the current...
When I combine BLE_APP_UART + BLE_APP_UART_c apps in last step "ble_nus_data_send" return error 4 from BLE_APP_UART part in multirole mode
BLE_APP_UART_c send without problem...
Hi,
I am working on having my device to perform a dfu over spi. I have been able to get through the init packet initialization and transfer, however, I am getting an error...
If my device only acts as a peripheral, does it need to respond to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST events? In other words, is BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST a...
Hello,
I added bonding to my BLE central device so I can re-establish known connections very fast. The bonding of the devices works fine but additionally I would like the...
Hi all,
I am using ncs version 1.5.0 and dk version 0.15.0.
I would like to rely on the CC310 piece of hardware to perform some cryptographic computation.
However, I...
Hello.
I have a question about setting MAC address.
For now, my device uses random static address from FICR.
And I also use "bt_set_id_addr()" function for test purpose...
Hello
I'm having some issues setting up monitor mode debugging with the nrf connect sdk v1.4.99.
I've roughly followed the steps outlined in this guide , the exact steps...
Hello,
I am trying to program my NRF52840 chip with the Secure Bootloader UART project, in addition to the BLE App UART project as mentioned in the title. So far, having...
I am trying to work with Bme680 with I2C communication i can read every value but i cant read air quality value its always at 806516 value and does not change . I thing configirations...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
When I use j-link soft uart all good
but when i disconnect j-link the soft uart will error
like this so�rceid=2, status=0 sourceid=3, status=0 sourceid=4, status=0
Hello,
I'm new to BLE product and nRF52840 dongle and DK are my first BLE evaluation kits. I've some experience in Arduino AVR microcontroller. My setup is as follow:
...
