i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi.
How could I set extended advertising through the 37 secondary channels as default, in an nRF52840 module which is using PHY_CODED modulation and running a ble_app_uart...
When working on adapting the bootloader for NRF52832_XXAB I noticed that -DNRF52 seems to define NRF52832_XXAA and later defining -DNRF52832_XXAB does not override it. I suppose...
If the Mesh DFU process fails (maybe a packet gets dropped or something), what happens? Will the device get stuck in an unknown state? What does the recovery process look...
I am trying to make the nrf9160 device work with our own AWS IoT account.
The nrf9160 device succeeds to run mqtt_client_tls_connect(). Then it runs mqtt_client_tls_write...
Hello,
I am using SDK12.3 and have problem with garbage collection (FDS module).
My apllication depends on timeslot, so that FDS is supposed to run together with Bluetooth...
Hi
I am writing ANT+ device on pStorage and want to read back from memory during ANT+ stack init. I am trying to change the Device name on this snippet
No luck so...
Hi,
I'm working on the ble_att_mtu_throughput example code on nrf52840(peripheral) & nrf52832(central) . SPI data is transmitting from TI(slave) board to nrf52840(master...
Hi there! I am developing a device with the nRF52810 that requires the following:
Receive audio over BLE
Store audio in memory
Playback audio on command
Would...
SDK 15.2 API 6.10 SES custom board
I am trying to get DFU to work and it is not seeming to work right.
I am trying to engage DFU mode by holding in button on board for...
Dear DevZonee's
Im trying to esablish a BLE connection using the following configuration of the peer-manager:
* LESC
* Just Works -> IO-Caps none (0x03)
If i run...
Hello
I am using SDK12.3 on nRF51822 chip using Keil V5 on windows 10.
I am using experimental_ble_app_buttonless_dfu example and bootloader_secure example.
They both...
Hello!
SDK 15.3
If I build secure_bootloader example project using Segger Embedded Studio it works, I can see it nRF connect.
If I build it using armgcc it does not...
Is there any actual difference between "Fast Advertising", and "Slow Advertising" - or is it just a way to easily specify two different sets of timing parameters?
The question...
Hi,
I'm having problems with the bootloader in SDK 15.2. I'm using an NRF52840, I don't know if the CryptoCell is giving me issues.
The DFU fails when checking the FW...
Hi All,
Sorry if this is a simple question, but I can't seem to find an example where the device is programmed as both RX and TX. (The examples have either one or the other...
