We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
I am using nRF5_SDK_14.2.0, I am using the watchdog, but I would like to change the reload value but I cannot do it.
I used this function but it is not working I do...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Hi,
It seems to be a bug in hal_device_reset() when using S132.
On line 8 above the function sd_power_gpregret_set() is called with the wrong arguments. The first arguments...
can I use an nRF52840 based BLE gateway? Backhaul would be either 10/100 Ethernet (via Wiznet or Microchip controller chip) or a cellular module. Is the clock speed sufficient...
I am unable to get 6 notifications per connection event. I am connecting two nrf32832's, one as a central, one as a peripheral. To make this as simple as possible, I limited...
Hi
We are able to provision several mesh-servers.
The log on the RTT-Viewer of the client looks normal:
0> <t: 915394>, mesh.c, 178, Local provisioning link established...
I am working with the peripheral/flash_fds in SDK14. I need to adapt it to use RTT instead of uart
I have made the obvious changes to switch from uart to RTT, eg substituting...
Hi everybody,
I'm trying to use the example ble_app_hrs with s110 on the PCA10001 Board and the ble_app_hrs_c with s120 also on an other PCA10001.
I changed some led flag...
I have already explored how to fix the related problem in the DevZone. I think the firmware of the ATSAM3U2CA-AU is erased. Here, I have two problems:
1, How can I get the...
Hi,
According to the code in PCA10059.h:
#define RX_PIN_NUMBER 11 #define TX_PIN_NUMBER 9
I would like to know what pins are related to number 9 and 11 in this schematic...
Hello,everyone.
If you have some suggestions,and you leave them, I would appreciate it very much.
I designed a pcb base on nRF51822. It can only be searched by mobile...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Hi, I want to reduce current my module.
I used SDK15.0.0ver, nRF52832
I have 2 questions.
1. I used app_uart_close();
But My module was reset again.
2. I want to...
