Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi guys,
I am using the RFduino nrf51822 chip. I am using the TIMER2 interrupt and it works fine. But when I try to use the BLE along with the timer interrupt both don...
Hi,
I have have one ble project which is using softdevice s110. so that i want to extend this project by adding DFU service to it like shown here
devzone.nordicsemi.com...
hi,
i have PCA10028 dk board. i want to flash code in this board using dfu. i have generated Zip file(both soft device and application(example ble_app_hrs example)) using...
I am using this DFU library github.com/.../IOS-DFU-Library . On iOS 10 while processing DFU I receive error RemoteInvalidState in didErrorOccur method with description "Device...
I want to know the maximum range for major and minor in Ibeacon frame, as it is of 2 byte can we set any values from 0 to 65535 or is there any limitation.
Hi everyone!
I'm using the nrf_soc API for get random numbers from the rng and erase and write the flash memory.
In my code, I include the nrf_soc.h file, in the header...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hello,
I tried to do DFU using MCP 3.10.0.14 and I'm getting the error:
"Error during firmware upload. Timeout while waiting for response for START DFU"
How do I increase...
I have secure dfu working on the pca 10040, and being able to download my own signed app.
However I want to turn NRF_LOG and at link time I get several messages of "._build...
Hi,
my application consists of long waiting time without connection (hours, possibly days, weeks), then a central connects and downloads data, and then again long waiting...
Hello all!
Sorry for what might seems an obvious question, my skills are what they are :-).
We have a small circuit based on nrf51822 chip.
Our software is currently...
Hello, I am new to embedded world.
I wanna know that how do i create a new template/blank for programming in uKeil?
Right now, i directly open an example from the SDK...
Hi there,
I am currently working on a project where I would need to use the Segger J-link needle programmer with 6 pin header. We have produced the board and after following...
Due to the PWM driver having intermittent issues we had to replace it with a TIMER/PPI/GPIOTE setup.
The PWM is working great in this way, but now I'd like to have one of...
Hi All,
i am using Stpm32 energy meter board.
i have gone through the data sheet completely.
i want to read and write the register values
i am trying to write 0xABCD...
