Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Im trying to provide DTM functionality for certifications tests. I can't setup an UART interface, I found the below code which tries to use DTM without UART. it uses channel...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
Dear all,
I have tried using a setting a break point in main() of my program. Without running the softdevice, it is fine to pause in the break point and continue to run...
Hi,
I am developing a product using nrf51822. While pcb designing I am getting a clearance error. Please let me know how to resolve it. All the dimensions are 8mil in clearance...
Hi,
I am editing my question:
I have seen some strange behaviuor I could not explain. In order to test it I have made the next test program:
I am using the application...
Hi,
I recently bought the nrf 51 development kit. Before implementing a BLE application on the board I wanted to start with a simple application of blinking a LED by pressing...
1.I have a nRF51_DK and nrf51822(waveshare core51822)
2.Keil 5.18v and all of the needed software were Installed
3.s130 1.0.0 or 2.0.0 and sdk9.0 or 10.0 were used ...
Hi Nordic Dev Zone, Ray Kampmeier here.
I'm building Direct Test Mode (DTM) into a production application that uses the 110 soft device. Unlike the provided Nordic examples...
Is there any way to integrate SoftDevice with entire project so I can get one hex from build? I am new to CrossWorks and nRF52 and I am developing BLE device. After getting...
I want to do firmware update over the air in a STM32F4xx microcontroller which is connected with nRF51822 chip via UART (TX, RX, CTS, DTR) and BOOT pins. ST microcontroller...
Hi
I can get the current time from the server using the time service characteristic. Which function should I use to set the RTC clock on the nrf 51 to the current time...
