I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi, I have a FEM module connected with spi0 on an nrf5340 running Zigbee. without the FEM module, the range of the device is around 10 meters (specific environment, not free...
Hi,
we would like to provision TLS tags / certificates for cloud authentication over Segger RTT on a custom device. We are using the Golioth cloud with the Golioth Firmware...
Hi,
I am working on optimize the SPI timing for an NFC reader IC which connected to nRF52840, to minimize the read/write time as much as possible.
And I notice that...
Hello,
I am evaluating the Thingy 53 + nRF7002 EB for Wifi and Bluetooth scanning.
But depending on which power source I plug the devkit, the wifi interface doesn't set...
Hello,
I just bought a nRF52 DK board (PCA10040, 3.0.0, 3023.22, 1050315142 ). It has a N5340 MCU near the micro USB port, and on the other end, it has a N52832 MCU. I have...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application .
Using nRF extension for VSCode, I've created a new application based on the...
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
Hi folks,
I'm trying to build an application with the CAF, and I'd like to use the sensor manager module, but I've run into a few problems -- any help would be appreciated...
I am currently developing with the nRF5 SDK and infocenter.nordicsemi.com is the best location to find information on this legacy firmware. I am aware that the nrfConnect...
Hi, I have problems with debugging for the NRF9160-DK. I installed the latest VSCode tools (as described here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.99-cs2...
Good afternoon,
I am trying to send some analog data from a function generator to my nRF7002 DK and visualize the output in Putty. I use printk to print the values and I...
Hello.
I modified multi-nus central example to connect with four peripheral devices. I don't use uart at all, I don't need it, I don't need routing, I just send 16B frames...
Hi!
I am confused regarding NUS, L2CAP, ATT and GATT.
We are using NUS with data length extension to communicate between two nRF52840 boards and want to maximize packet...
Hi, here in the documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/config_and_build/board_support/processing_environments.html ) for the latest...
