Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I'm working on a project with the AD5940, and it looks like this case did the job.
However, I am using NCS v2.2.0 and not nRF5 v17.1 - so code translation is required...
Hi,
we are using nrf52840 and nrf SDK-16.0. we have achieved simultaneous connection and data transmission for 4 devices in Ble 4 (i.e. 1 Mbps PHY).
Now we are trying...
Hello Everyone! I am working on a zephyr project based on nrf52832_mdk hardware. I have a code that transmits data over BLE. The BLE connection name is, let say zephyr-connect...
Is there a way to modify the PHY layer, or SoftDevice, so that a timestamp is immediately read from a timer and forced into the manufacturer data right before transmission...
I have an application I am working on, and I created a custom structure rx_servo_t. The structure is meant to provide methods for controlling some off board motors via GPIO...
Hi,
We need to integrate a testing mode within our firmware that uses Nordic controller to do BLE functionality as we want to achieve single image solution for production...
I'm working with a BLE peripheral application that must transfer large amounts of data to a phone central. The application uses the MTU negotiation to determine the max notification...
Hi,
I'm evaluating the nrf7002 for use in a monitor mode device. I'm using a nrf7002-dk, nrf connect sdk 2.6.1.
I'm working off of the monitor mode sample here: https...
Hi,
We have several hundred devices in real time deployment and find the typical DNS/Cellular connectivity issues during the day that we generally solve with delayed connection...
Hi there,
I must interact with an I2C slave that sends variable-length messages. The first byte of the transactions describes the length of the remaining bytes.
i2c_write_read_cb...
Dear Support,
we would like to know what is the total value of the capacitance and the inductance of the nRF52805 (for ATEX certification). I can not find this information...
We have project using the common Matter Code base from SDK 1.6.1 and using a variation of the code to act as a switch sensor device time. This seems to work pretty well; however...
I need to add tx power to my BLE advertising, but I need to ensure it is in the Scan Response only not the main AD PDU.
Also, I change the Tx power by code using the function...
I have a PCB made for my project. I want to read log from RTT. When I try the same software in the development kit, I can read from RTT. But when I want to read from the PCB...
Hi,
I have a proyect with the following memory requirements.
The current project has a propietary bootloader and bare-metal application. Therefore there is no Zephyr...
