Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
I tried to establish communication between the two development boards and the phone. The specific process is as follows: One development board works in slave mode and the...
hi team,
I am using nrf52840 device and version is nrf52840_xxAA_REV3.board version is pca10056.i have one doubt every file and programme's are flashing throuh interface...
Hi,
I'm doing migration from sdk 1.9.1 to sdk 2.1 according to procedures mentioned in Migration Guide. All dtsi migrations were done sing script and later on manually reviewed...
I am using the NCS (2.0.2) SMP SRVR example with the bt-overlay.
I can connect via Bluetooth, but once I start the DFU update via nRF Connect I get an "Authentication is...
I have AES ECB encryption working on the NRF5 system, but I cannot get it working on the Connect SDK.
I have found CONFIG_CRYPTO_NRF_ECB config, but this seems to require...
Hi!
I'm trying to run SPI slave on nRF5340 - doesn't work - project doesn't even build, the SPI master is running.
Can I see an example of NRFX SPI Slave for nRF5340?
Hi, I have several issues just to start off with. One is when I generate support information, it does its thing, and then stops, and I have no idea where the support information...
Hello,
I am looking for the detailed schematic of the debugger board which is packed along with the Thingy:53.
I need to understand the detail pin configuration for...
Hello there,
If I init a UARTE module (nrf_drv_uart_init) with e.g. Pin RX = 3 is it already enough to just disable the module (nrf_uarte_disable) so I can use the RX...
MCU: nRF52840
IDE: Keil uVision
SDK: 15.2.0
Board: Custom
Hello,
I realize there are a ton of threads about this, but none address the specific question I have...
Hello,
My board is powered by lithium-ion batteries.
It works from 3V to 2.1V. And It stop working at 2.1V.
After discharge, I re-charged battery. But It doesn't work...
I want to achieve reproducible builds on my development machine and a gitlab CI/CD server. So far the generated binary differs if I build locally (VS Code + NRFConnect SDK...
nRF5_SDK_17.1.0_ddde560
nrf52832
Cache overflow at baud rate 921600. I use the register to complete the serial port driver. I don't know how to use registers to implement...
To the kind attention of Nordic support team,
I'm testing a freertos project, with softdevice and radio notifications. A constant number of notifications is queued before...
