Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
Dear Nordic Support Team,
We are developing a Matter device based on the nRF54L15 using NCS 3.1.1 . We started from the Matter light example provided in the SDK.
We encountered...
I have a combined asset_tracker_v2 and central_main. I can connect perfectly and receive data from a single BLE advertiser. I need to be able to connect to 1-4 simultaneous...
Hi,
I’m using an nRF5340DK with nRF Connect SDK 2.9.1 , configured as both Central and Peripheral with the nordic SDC running the network processor Goal: allow the board...
The firmware always halts execution during boot after providing these logs:
26/05/22 10:38:33.925 89737.861 13892 0 E: Device id 00 00 00 does not match config 1f 16 01...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
I’m working on a custom board based on the nRF9160 (SICA variant) and trying to enable MCUboot + TF-M with sysbuild. I’m running into an issue where the system never reaches...
I’m using the RADIO peripheral for BLE 1M connection-event RX→TX turnaround.
Current flow:
1. RADIO receives a data PDU. 2. RADIO reaches END/PHYEND and disables. 3. In...
Hello Nordic Support,
I am using nRF54L15 with NCS v3.2.3 .
The device is using Legacy Connectable Advertising with Flags and Complete Local Name in the advertising data...
Hello,
I have a few questions about the nRF9151 DECT NR+ modem.
I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hello guys,
Im developing RTLS with DWM3001C and right now Im working on personal tag powered by CR2450. So naturally, power consumption should be as low as possible....
