Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
I am evaluating Zephyr mesh and implemented two timers; one triggers at every 2 mS, the other triggers at every 500 uS.
I put a code in both timers' events to toggle...
Hi, Our platform is NRF-52833 Our project use RS485 bus (nordic's uart + a 485 chip) to communicate with other device. And we choose the libuarte to be the uart handler to...
Hi,
In the nRF_SDK_for_Thread_and_Zigbee_v4.1.0, in examples/thread/NCP/radio folder, there is no option for compiling the firmware for PCA10059.
I want to run RCP firmware...
Hello guys,
I'm trying to interface ds18b20 temperature probe and I'm using this code , In termite its showing output as -0.062500 I don't know why can anyone tell what...
Hello,
I'm using NCS 1.4.99 with a nRF5340DK and want to use the hardware CS of the SPI and also use BLE.
Here is a simple code that work on a nRF5340PDK but only work...
Hi All,
I was just reading the white paper on RF testing guidelines, and I noticed several times there have been mentions of "nRF Performance Instructions" for each of...
Hi,
I am working on NRF52832-based board, with SDK 15.2.
My BLE device is protected with Legacy Connection OOB preshared key.
I would like to use Android NRF Connect...
Hello dear,
I am installing Embedded Studio on OSX (Catalina), and I following the nRF Connect step... all goes fine, but when I try to use "Open nRF Connect SDK Project...
I'm trying to see debugging info with nrf51 dongle.
As far as I can tell I just need to use:
#define NRF_LOG_MODULE_NAME "APP"
#include "nrf_log.h"
#include "nrf_log_ctrl...
On a nRF5340 DK the sample ncs/zephyr/samples/subsys/usb/cdc_acm runs fine. However, if I add "CONFIG_NO_OPTIMIZATIONS=y" to prj.conf I get faults (see below). Any ideas why...
Hi,
I am preparing Windows desktop application which will use nrfutil for DFU of the products (containing secure dfu bootloader). I tested nrfutil v6.1.0, v6.0.1 and even...
Hii guys,
I am trying to establish communication between two nrf52 module.
My application is as following
1. I need a central device which can work as master and remains...
Hello, I am stuck initalising both TWIM and UARTE. I am focusing on the TWI Scanner example but using TWIM instead of TWI. No matter what I do I cannot get past the initalisation...
