Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
Hi can somebody help why nrf52840 doesnt be reseted when you press SW5(if boot/reset)? I have alredy with tried with few examples flashed on nrf52840 and in Segger IDE set...
Problem :
I have two I2C devices and would like to connect them both to nRF52840 DK on different I2C pins. According to datasheet nRF52840 has two I2C pins (P1.00, P0.22...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am trying to build out a button pressing scheme for BSP on a custom device with 15 buttons operating on a BL652 Laird Module (underlying nRF52832). After modifying...
I'm working with the NRF9160 DK and have found the sample times for the ADC to be abnormally long. I am sampling three channels and seeing a total time for the ADC read of...
Hey guys, I am using 2 nRF52832 boards with a PCA10040. I program my boards with the BLE UART central and peripheral examples. I was wondering if it is possible to, and if...
Hello,
I used 3 nRF52-DKs to run the pb_remote and it ran well with the Mesh SDK v0.10.1. Then I created my own project and copied the code from the pb_remote client and...
Hi,
I'd like to test the sample udp_gps but SES throwes an error and a warning. The warning says: Path/udp_gps/prj.conf:36 warning: attempt to assign the value 'y' to the...
I'm attempting to use the serial DFU bootloader to update my nRF52832 firmware but am unable to. I started by following this guide though I changed some things so that the...
Hello,
Let me introduce you to the issue:
I am working on a custom firmware for a custom hardware, based on the nRF52832 and SD S132, as a central which need to connect...
Dear Nordic Support,
When I got my nRF9160 DK, I ran the getting started successfully then I followed the instruction from the 2 below links:
https://devzone.nordicsemi...
Hi
I have an issue with updating DFU by nRF Connect on iOS 12. I receive the error:
Although it is working on Android without any problem.
I am using softdevice 6...
During WDT implementation I went into flash loader problems.
It is not possible to start a new debugger session (flashing) and the system is stopped at the progress bar...
Hello,
we have bought a bmd340 low energy module that we mounted on a selfmade breakout board. Now we want to read an analog value into the bluetooth module. How can we...
