Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
[nRF5SDK15.2.0, KeilMDK, Windows 7]
the code runs ok in the customer board, and the print log as fallows: [00:00:00.000,000] ble_scan: Adding filter on CPS_xxx name [00...
Dear nordic,
I started to integrate PCF853(RTC module) using i2c. but its not getting proper output can you help me what wrong i do?
slave address:- 0x51
read register...
Hi Sir
I enabled the "APP_UART_FLOW_CONTROL_ENABLED", but I measured the CTS / RTS pin always is low during data transmission.
Is it normal ? How to check UART FLOW control...
Hey, i have got UART work on my Thingy52 with ANA/DIG0 and ANA/DIG1 as receiver and transmitter but when I am trying to use EXT0 and EXT1 as receiver and transmitter it doesn...
Hi,
I am new to embedded device development and I am wondering if I could get some help on SPI control from nrf51422/51822 chip with dev kit to AD9837 wave generator. I...
Hi,
I am try to create a PWM output which can move the specified number of steps.
Please find following source code
After I execute above problem, I can get following...
Respected sir,
There is added external reset button at SRU532 module, and changes are given according to it using wakeup button at code.When wakeup button is used then some...
Hi all,
I am trying to implement a multilink central with UART. I had looked through the forum on all discussions in about this and followed this thread to come up with...
Hi guys,
I'm testing the 52810 duf function.
hardwar: 52810
using SDK: 15.3.0
softdevice: s112_nrf52_6.1.1_softdevice.hex
download software: nrfgo Studio
bootloader...
I am trying to flash the blink example from SDK v15 into my custom nrf52840 board, I am using pc10056 example.
I connected my ulink2 to swdio, swclck, gnd and vcc of my...
Hi,
Since the last update of the 'Getting Started Assistant' (0.9.0) from 'nRF Connect' 2.6.2 on Windows, I can´t set up or compile any sample of the SDK for the evaluation...
So I've been having a problem the last few days - using the NRF52832 we have an SPI chip connected his chip requires a clock signal (1MHz) that is being generated by the NRF...
We have written code based on SDK V12.2 and found it doesn't support power saving mode. Given that it's very complicated to transplant to higher version, how can we fix the...
Hi,
I want to interface two QENC with nrf52840, I saw QDEC example and it works as expected.
The problem I am facing is that QENC has four pins of which two are for power...
Hello,
I am having strange issue. I'm getting some data from custom service and characteristic. I can see the data being received is correct. However, if I try to pass the...
