I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello,
I am looking to get started with NRF52. I am very familiar with TI BLE so not a beginner.
I am looking for a high level introduction to the nordic soft devices...
Hello,
i am new to BLE,
I am using the iot S1xx Softdevice on the nrf51 Dk in order to test ipv6 connection, and now i want to add advertising with the Eddystone protocol...
Sorry I am new to this. Therefore this question may seem to be odd:
I want to build a temp monitor using an nRF8001 (BLE Board Adafruit) and send this data to my mobile...
This is the code I am using to wakeup my system from OFF. It is not working. Kindly Help.
#define Pin_0 0
static void gpio_init(void)
{
ret_code_t err_code;
...
I am creating a system (nRF52 SDK11.0.0 s132) that will get a data ready interrupt on a GPIO (configured via GPIOTE with a handler) from a sensor every 4ms. The sensor has...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
We've currently only been developing our application in C. We now have a couple of C++ libraries we'd like to use and are having trouble compiling the mixture of C and C+...
On a custom board using the nRF51822, with SDK 11.0.0, SD s130 and gcc, I'm seeing the following stack trace when doing some TWI operations to program an accelerometer:
...
I have to send a data to more units, i have found problems with multiple ACK return signals (I think this is the problem).
So i'm trying to send data with no ACK.
For this...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
Hi.
I've played around with the android application (based around google gatt example, but used in gatt server -mode).
How is the example expected to be handled? In...
Hello everyone,
I am currently trying to make simple exchanges with an NFC chip using SPI.
Configuration is: nRF52 on dev board 10040 with example from SDK12 located...
Hi,
I have such code:
static buf[9] = {initializers};
for(i =0;i <9;i++){
while(app_uart_put(buf[i]));
}
I always get "0" before the actual buf content and the...
Hi
I've implemented a peripheral with bonding support by the peer manager. Additionally the device should scan for bonded devices by using a whitelist. I used the function...
