Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi,
I just downloaded the Utility app for the ble apps(nRF518 SDK) checking on my i5 at iOS 7.1.2. I have tried to connect the apps(hr, proximity) of Utility, but there is...
I changed the dfu start address to 0x00 and application start address to 0x8000.
The application use the RTC0 IRQ to count the timer,
but the RTC0 IRQ did not work correct...
I've been successfully using IAR and I-jet with the 51822 and S110. I can build, download and run under the debugger with no problems.
I recently switched to the 51422...
Has anyone has any success flashing a nRF24LU+ dongle NOT using the official dev kit ? I'm attempting to flash using another microcontroller programmed as an SPI Master so...
I will be happy if someone points out this is a newbie problem and not something weirder...
Running on Win7, 64 bit BTW...
I recently received the nRF51 eval kit. I...
Hi,
I am trying to connect my msp430f1611 microcontroller with the nrf8001 bluetooth chip. I read this thread ( devzone.nordicsemi.com/.../) and it seems very helpful....
I have been trying to implement a SPI Master on the nRF51822 Eval board in order to read data from an Analog Devices ADXL345 3-axis Accelerometer. I chose to start with the...
Hello,
Firstly, the nRF5122 Product Specification v1.3 Section 4.2 says that TIMER0 is 32 bits wide.
However, other product specs seem to mention 16/24 bit timers, and...
Hello Nordic people!
I'm developing my first firmware on nRF51822 and I need help with BLE, profiles and SoftDevice S110 stack.
Application it's a speed sensor for bicycles...
I have nrf51422 dk. The boards I connect to 3.3V power and via jlink to my pc.
I use the JLink command line tool.
I can not access the chips. Erasing is not possible and...
Hi there,
I am using Eclipse and GCC (codesourcery) as development tools.
In the gcc makefile, once provided by Nordic with the "button_radio_example" are two lines...
Would the example github.com/.../require-encryption-5.1.0
compile without any extra configuration ?
I am trying to build it in a Keil uVision v.5.12.0.0, but I have some...
Hi,
I have an idea to implement BLE based access control application. I considered nRF51822 based Peripheral device & iOS application for central device
Both the Central...
We are in the process of creating our 2nd pass boards with following components to achieve good RF range>20 meters. We are considering discrete BALUN components and SMD Chip...
I see 5V pins on the schematic for the new nRF51 development kit. If I power the board via USB, I understand that 5V is regulated down to 3.3V for the chip. Is the source...
