This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Hi, in our project with the nRF5340 we desire use the nRF21540 to have a long conection for BLE, the problem is we don't have any pin free in the nRF5340 to manage the nRF21540...
I have configured new UART in zephyr.dts device tree like this" "/ { chosen { zephyr,console = &uart1; zephyr,shell-uart = &uart1; zephyr,uart-mcumgr = &uart1; zephyr,bt-mon...
my device acts as ble periph ,case BLE_GAP_EVT_DISCONNECTED in ble_evt_handler , if do m_conn_handle = BLE_CONN_HANDLE_INVALID,current changed to 2.5mA, if dont, current is...
Hi,How can I force mcuboot to use a specific serial port for logging?
chosen {
zephyr,uart-mcumgr = & uart0 ;
zephyr,console = & uart1 ;
zephyr,shell-uart = & uart1...
Hi,
we have created a new product prototype where audio streaming is the functionality. 2 different HW revisions were so far built, the software originally is built to use...
I am trying to make the broadcast _audio _sink work . It is always stuck with the following logs :
Broadcast Sink created, waiting for BASE
which then times out with ...
We built a custom version of the Direct Test Mode sample in our firmware, using the USB shell to interface with the test operations and removing the UART or HCI interface...
I have a IMU whose interrupt is connected to GPIO0.11 which is also nrf-gpio-forwarder GPIO (which I dont use)
I managed to get it to work but lost that progress and cant...
Dear Nordic
Question 1: How many bytes can the Rf Tx of the current Nrf52810-QFAA transmit at a time? Now I can only send 256 bytes at a time. Can I send 512 bytes at a...
Hi there,
I always have to start up nrfconnect-5.0.2-x86_64.appimage and then select the power profiler. How can I directly start up the power profiler?
I can see that...
Hi there
I wrote a program (include of advertising, pairing and connecting over service, characteristics) for nrf51822QFAA and work well for C0 build code (nrf51822QFAAC0...
I want to know the power saving mode of nRF5340. Dose this chip set have the following mode ? 1. each BT products connencts, however, the data were not send. above condition...
Today I tried to use the bt_conn_le_param_update() method to update the connection parameters, using the following values.
interval_min = 3000
interval_max = 3000
latency...
Hello,
We can successfully build and flash the ncs/application/asset_tracker_v2 example code in nrf9160. But when trying to boot up, it throws the following error:
**...
Hi there,
I'm using a nRF5340 to generate an 8MHz signal and would like to force the HFXO to always be used as the HFINT is not accurate enough. I have verified this with...
