I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
Hi are there any image/bulk data transfer demo to test throughput between nRF and iOS application
There is one for older nRF5 SDK but couldn't find one for nRF connect ...
Hi,
I use two nRF52833-DK boards for uart communication (both using pin p0.06 for TX and p0.08 for RX), with their TX and RX and GND pins connected to each other, and perform...
Hello
I am facing issues while pairing nRF7002DK with nRF WiFi provisioner app, when I build the app (provided by nordic and hosted on github). However the pairing is successful...
Hello. On july 26 at the same hour, about 30 of our cellular modems stopped sending data. They are all using Verizon firmware. The units using Hologram firmware are still...
Hi
I have 2 BLE boards with some environment sensors on them.
I need to synchronise the 2 boards with < 1 mili second precision.
one board is configured as central,...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hello,
We are using Zephyr OS and SDK v2.5.0 on nrf52840 chip. We have noticed some delay between spi_write and spi_read of 29µs,which is critical for our goal. Comparing...
After I installed nRF Connect SDK 2.7 and tried to run the pre-release version of VS Code extension, I am now compleatly unable to make nRF Connect for VS Code function. ...
I' m using custom board of nrf5340 with nrf7002, and the SDK version is ncs v2.5.2.
I've tried to build and run, but the log in RTT viewer is only print the line "Bringing...
Hi nordic:
I am currently using NRF52833 to create a MESH product and would like Bluetooth to send AOA tag information in MESH mode. Is this feasible?
Best Regards ...
I encountered the following error while building my ZigBee app on a CI (dockerized Linux container), after bumping the SDK from 2.6.1 to 2.7.0.
The part "nRF52840" in...
Hi All, I am using an nrf52832 and using NCS version 2.6.0. I am having an issue where I am trying to initialize and run a thread, but the thread never runs. I have tried...
I want to set the CONFIG_CAF_BLE_ADV_FAST_ADV Kconfig option to make the Peripheral initially advertise with a shorter interval,but after adding some dependency configurations...
hello.
Currently I am implementing BLE Multi advertising in
NCS SDK: version 2.6.0.
I have a question during development through the samples/bluetooth/multiple_adv_sets...
Hello,
I am working with the USB CDC ACM Sample Application from NCS V2.1.0 on nRF52840DK and have encountered an issue when attempting to replace the UART_INTERRUPT_DRIVEN...