Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I use `west debug` to start `gdb` for debugging nRF5340DK
when I use `west build` to update the image, I use `load` command inside gdb CLI, the new `zephyr.elf` is loaded...
I don't know if this is a hardware or a software problem. My nRF52832 code runs correctly on a PCA10040 development board (UUID = E9:4A:AF:04:D2:16). My custom hardware advertises...
My software sent 2422, and I saw it on the net. 2417 also has one.
And the same goes for everything else, which is basically 5M off.
What is the reason?
Hi all,
I am working on troubleshooting intermittent application resets with an nRF52840 and nRF Connect 2.6.1. Codebase is small, complexity of the project is still small...
Hello,
I'm working on a BLE central multilink application, where I want to get the list of all peripherals in range, In order to let the user select the needed periherals...
I implemented UART communication as follows, but occasionally the same data is sent twice.
Enter the critical region (app_util_critical_region_enter).
Store the transmission...
hello!
I'm using 'NRFX_LOG_INFO' for debugging purposes. However, the code seems to stop progressing when 'the NRFX_LOG_INFO' statement is removed from the section below...
Hi,
I am using an nRF52 DK board to perform some very simple tests. All I need to do is receive a line of text over serial, perform some calculations and return another...
HI
I'm trying to use lpcom to detect when the battery voltage is dropping.
The configuration is as follows: 5V battery voltage output is reduced to 3.0V through LDO...
For my application I need the UART TX/RX pins pulled low until I am ready to turn on the UART. Is there a method in Zephyr to do this? Currently when Zephyr starts it reads...
I saw some similar question, but none is what I am experiencing.
I notice some weird behavior while testing DMA mode, so I made a simple setup:
I set the DMA buffer to...
Hello everyone,
I have two devices: a Thingy53 acting as the peripheral and an nRF5340 acting as the central. I have a characteristic in a service that I want to modify...
can I send the data from the internal sensors of the stm32l4 card to nordic thnigy 91, then the latter send the data from its internal sensors and the data which is already...
