Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi all. I am using nRF5 SDK 15.0.0 and the S140 SoftDevice v6.0.0 to develop on an nRF52840. Due to software infrastructure constraints, I am unable to implement DFU using...
Hello,
I have a use case where I need to use UART_RTS and UART_CTS as GPIO for toggling the led. I also want to use the other two pins UART_TX and UART_RX for handling UART...
I have created an application that initiates a timer for 30 seconds and when it expires it calls an expiry function that switches the system off, if no button is pressed since...
If you try to write a program on a board with nRF5340 installed, an error will occur.
I can write to other boards using the same J-Link, so I don't think it's a J-Link problem...
Hello all,
I have scoured the devzone and other blogspots to find an answer to this but so far have come up short.
in short i want to use one NRF552-DK with the adafruit...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made DFU procedure...
Hello,
I have a problem with a custom board with a nRF9161. I am trying to connect the board with the nRF9161 to the LTE or NBIOT network, and the board doesn't seem to...
Hi,
We've got a board with a fairly limited power supply in production and it's expected to brown out under certain conditions. As such, I need to verify the reset loop...
Hi community,
ncs-2.6.0 I'm using.
I'm trying to enable bmi270 as I enabled adxl362(is already working), both are connected with SPI.
but it shows me this kind of...
In my project I use MPSL for a combination of BLE, ESB and flash sync. The BLE/ESB timeslot handling was implemented following this example: https://github.com/too1/ncs-esb...
Where to find the sample for nrf5340 net core that is written by default. I mean when I use BLE observer sample with zephyr controller there is some code that goes in Net...
Does mcumgr support relay functionality? On one device, I have a firmware image stored in external flash connected to a 9160 and need to relay that image via UART to an on...
In case of peripheral losing keys, but client(Android nrf connect app) still has them. ( shows it is in 'Disconnected + 'Bonded' )
On the next connection attempt, there...
Hi,
I'm trying to build my custom test project with the nRF Docker in accordance with https://github.com/NordicPlayground/nrf-docker .
I've started with this simple script...
