I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
When trying to receive an LE Audio broadcast, issuing an HCI_LE_BIG_Create_Sync command with parameters obtained after scanning for ISO broadcasts, the
HCI_LE_BIG_Sync_Established...
Hi Team,
We have started our cellular development using nRF9160 modem using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going...
With SDK 3.0.2 and 3.1.0 we noticed that during a build, even a 10-core i7 becomes almost unusable. The reason seems to be that all cc1.exe compiler processes run at normal...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hello,
I am attempting to program to a custom board using VS Code. I am using the Bluetooth beacon advertising example from BLE fundamentals Lesson 2 Exercise 1.
I am...
I am experiencing an issue with my Tenstar nRF52840 Pro Micro board, which utilizes the Adafruit UF2 bootloader. When attempting to flash new firmware by copying a .uf2 file...
Hi my name is Assaf im using Nrf9160 on custom pcb with SDK and toolchain v2.5.2. I made modbus code which works just fine but when im enabeling the MCUBOOT related configuration...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hi
I notice there is a statement in nRF7002 dts:
I am wondering if I could always use the highest TXP 0x54 for all modulation indices to achieve optimal communication...
I attempted to connect the central device to the peripheral device.
Both sides are custom boards of nrf52832 and both are based on nrfSDK v17.
The log output on central...
When advertising using Coded PHY with the nRF54L, the reception rate is half to one-third compared to 1M PHY, even at short distances (sufficient RSSI). The receiving device...
Hello,
I am using a custom NRF5340 board and trying to run SPIS related code. The issue I am facing is that MISO pin kept low during the complete transaction . My pin configurations...
Hi, I have been getting randomly errors status from pmic measurements including status 64 (trickle timeout, I presume). Do you have any sample code to handle errors as per...
This is a custom board with nRF54L15. I have the following peripherals connected:
I2C30 SDA:P0,02 SCL:P0.03
I2C20 SDA:P1.13 SCL:P1.12
UART00 TX:P2.02 RX:P2.00
I also...
