I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi
it's possible configure the FOTA bootloader (SMP service) whit only one partition, for large application.
I using the nRF52-DK and have only 512KB of flash, and my...
I have trouble getting NFC-pairing to work in nRF52840 running SoftDevice 7.2 based on SDK 7.0.2. The observed behaviour is that the NFC Field is detected but nothing more...
Hi,
I add a new service about DFU of my FW，so three was a problem when it go into "ble_nus_init()" will return NRF_ERROR_NO_MEM, I have read serveral tickets about the same...
i have used "BLE_GAP_PHY_AUTO" in scanner code
actually it should scan "phy coded" and "non phy coded" aid values .
but in my case getting i was getting both "phy coded...
I have a project to use NRF52810 to connect the App. When testing it, I found that when it was successfully connected to the NRF Connect tool, it would automatically disconnect...
Hi, Dev Zone.
thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
1st_question <- this is my first question links
main problem...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
My project has requirements for tow...
development tool : Segger Embedded Studio
SDK:nRF5_SDK_17.0.2_d674dde
it always takes long time to build project
build log:
Building ‘blinky_pca10056’ from solution...
Hello all,
I am developing an application from the ble_cgms example on the nrf5_sdk 17 using the Softdevice S132.
I have implemented a gpiote interrupt whenever the state...
Hello,
I just received nRF9160DK(PCA10090, 0.8.3)
I followed nRF9160_DK_Getting_Started_Guide doc.
But, I hare some issue to activate iBasis Sim card.
It keeps...
Hello, I am using the latest version of pc-ble-driver combined with a pca10040 and I am attempting to write large data packets (200 bytes) to a peripheral. I compiled the...
Hi,
I have tested FOTA code in nRF52840 DK and it works perfect but i have custom board build with nrf52840 when i implement the code it doesn't get start
custom board...
I don't have time to learn the massive API for nRF52840 so I am hoping someone can provide a small
snippet of code (and instructions to put on the dongle) to do the following...
