Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi,
For Direct Test Mode on nRF Connect for Desktop, I have confirmed that Constant carrier can be selected.
The log was obtained at the time of the following settings...
NCS Release v1.5.1 now supports PA LNA, couldn't see any BLE examples on how to configure and use PA/LNA. could you provide any instruction/guidelines on how to enable/use...
Hello.
I'm using the NRF52832 with I2S module connected to TLV320DAC from TI. I've configured the DAC and I2S module successfully. I'm getting audio output (simple sine...
Hello,
I hope you are well.
I am currently working on interfacing an INTAN RHD2164 chip with the NRF52840. This chip is connected in SPI with the NRF52840. The only problem...
I tested NB-IoT and MQTT in NRF9160, and the device could normally search for NB signals and connect to our background through MQTT protocol. After the device uploaded data...
NRF52840, S140, SDK 14.2
I am trying to write to an SD Card. But whenever I insert the card, I get a failure on ASSERT. I believe this is because I am using P0.0 as the...
Hi Nordic,
I understand that there's a way to monitor the RSSI of a Bluetooth connection using appropriate API from softdevice library. But we are currently developping...
Hi,
I'm currently working on a ble mesh project with 2 nodes using nrf Connect SDK v1.4.2 with toolchain 1.4.2:
Device A with Time Client Model - nrf52840
Device B...
Hi.
I would like to flash an external sensor with the Jlink and then to "talk" with him through the internal sensor.
Can I know which sensor an I flashing? All the time...
I handle events directly by invoking the following code after the sd_app_evt_wait(); call:
I poll the events and dispatch them to my handler as needed.
Now if I do this...
What is the operating temperature range for the Nordic Thingy 52? I cannot find it anywhere in the documentation, but there is documentation on all its other sensors.
hi,
After the TX interrupt event occurs, on_radio_disabled_tx() is executed.
There is a timeout event for receiving an ACK. I noticed that the timer timeout was set...
Hi
I'm a bit unsure as to how to interpret the documentation. It's my understanding that zephyr v2.4.99 is an unstable development release. But it seems to be the only release...
Hello,
4-byte long SPI messages, "1234", are sent to nRF 52DK. The code in DK is attached below. The XFER_DONE event is created before the message ends, which happens very...
I thought this would be rather simple as I would design a BLE peripheral in the usual way but the source of data for the peripheral comes from a sensor sending nonconnectable...
