I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
hi ...
how to merge the serial uarte and ble_app_uart .... i want to getting the data through the serial uart and i need to transfer the same data over ble .. please guide...
Hi,
I have implemented a hx711 sensor readout with PPI, using SPIM and PWM peripherals. But for this is needed 4 GPIO and one external OR Gate. I wait for a LOW pulse on...
I came across the nrf-connect SDK sample UART : https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c . I was wondering whether...
Hi team
I want to config interval via LL_CONNECTION_PARAM_REQ.
But nrf5 looks like use L2CAP CONNECTION PARAMETER UPDATE REQUEST to send request to change config.
But...
Is there any reason the pin reset hold time is not mentioned in the nRF52832 product sheet? I've seen in the forums that it is same as nRF51, which is 0.2 uSec but I would...
Hi
We are using BL600-SA in our project. I need to configure NRF51822 transmit power so that it is discoverable at particular distance.
I am using softdevice S110 and...
Hi.
I am newbie and trying some sample examples from nRF52832 SDK for mesh to gain knowledge of Bluetooth mesh
I have nrf52832 Development Kit and I am trying examples...
Hi! We're developing a BLE-sensor for tracking small animals. In the past we've used a different brand of BLE-module but we're looking to switch to the nRF52840. As we're...
I want to use my "nrf51 DK" module as a BLE sniffer for which guide is provided at https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf but I also need " nRF Sniffer...
Hello,
I cannot connect Thingy91 to NB-IOT or LTE-M network. I am in the UK, so I am trying the NB-IoT with an O2 sim card. In LTE Link monitor I am unable to get a connection...
"There was an error adding your device. It wasn't found. Is it connected?"
IMEI and PIN entered several times.
I do not want to post the ID's here.
By the way: HW...
We are producing a batch of nrf9160 based devices and will need to upgrade the modem firmware, this will be much easier if we could do this through the command but I saw on...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I'm using the nRF52DK as a nRF Sniffer for BLE, following the directions in the nRF Sniffer User Guide v2.2. I'm using v2.0.0 of the sniffer, along with the Profile from v2...
When importing projects into SES, it does not appear that SES can determine configuration macros.
For example, in the mqtt_simple project, the function "modem_configure...
