Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Example Project: UART/Serial Port Emulation over BLE
My Environment: Segger Embedded Studio v3.52, Nordic SDK 15.2, Soft Device s132, nRF52 DK, nRF Toolkit for iOS
It...
Hello,
I have several questions regarding BLE beaconing and scanning that I feel are pretty basic but I can't seem to find the answer. I have a nRF52840 Dongle that uses...
Hello,
Thank you for considering my inquiry! I am looking for an example project with the firmware to run a gateway through the PC, nRFconnect software, and a nRF52840...
Hi,
I'm developing an application with the following hardware and software design components:
- nrf52840 DK with attached sensor
- nrf52840 USB dongle attached to debian...
Hi, I have some issues with my eclipse setup, I have installed all packages and followed the tutorial ( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development...
Hello,
I am working on bootloader on nRF24LE1, for which a protected region should be configured. Therefore, I need to change NUPP in infoPage.
So my question is, is there...
Hi.
I watched the examples and docs with the on-off model. I tried to run these examples and configure. I don't understand when I need to use a server model when client...
I am seeing some behavior in BLE advertisement mode , that I would like to get feedback from expert in this forum. I am using modified Keyboard HID example, using nrf51 BLE...
Hi,
I'm using nrf52DK and 12.3V SDK .
in keil i can able to go to the debug session but when i press run button it is not working.
what could be issue ???
I have enabled RX address 0 only, (value of RXADDRESSES field is 0x01)
But still I got a received package interupt where RXMATCH has a value of 0x07, indicating that I...
Tx Radiated spurious emissions (1-18GHz): should be able to force the radio into a continuous transmit mode on a specific channel. The device should be transmitting with as...
Hello,
the BT specification states the following:
Is this particular requirement to be taken care by Nordic's customer using the BTIC? i.e. LE PHY qualification test...
Hi,
I want to use bsp_event_handler in SDK v11.0.0 . But the code is not getting compiled.
On building, it throws an error "error:#20: identifier "BSP_BUTTON_ACTION_RELEASE...
Hi,
I'm using NRF_LOG to print information via RTT backend (RTT viewer v6.20) and it has been working so far. After adding a single call to a function that reads 128 bytes...
