Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,guys
I got a problem. I tried to create a service to control led over BLE, when i finished, it can advertise, everything was ok. But when i tried to write 0x01 to control...
BT832 connect to a passiv MEATER temperature senor. How should I configure the Device with AT-commands. I use Docklight to send AT-Commands from my BT832.
Hi Team,
I want to connect the nRF52832 based custom board to AWS-IoT cloud.
The Simcom 2G module is interfaced with nRF52832 over UART.
Can someone guide me from where...
hello everybody,
In my application i want to check if a password is set, to enter bootloader, otherwise don't start the bootloader.
This should work without bonding. ...
Hi, I'm new in the use and development of chip.W here do i start to develop myself?
eg my first aim is to make bluetooth headset compatible with android. Can you help me...
Hi, I have been looking at the following document nRF9160_OPS_v0.7.1-1510217.pdf which I had downloaded from the Nordic website today. In particular the layout guidelines...
Hi,
I run the "ble_app_uart" from sample program and leave it as it is. The program ends in NRF_BREAKPOINT_COND with "Fatal error" after a while. It is displayed as a screen...
Hello
I am using the nRF52832 with SDK 14.2, JLinkRTT Client, and SEGGER IDE. The system simultaneously runs a soft DAC, IMU, digital potentiometer, and provides variable...
Hi all!
I want to use the BLE stack by Nordic. I figured out that S132 is the appropriate HEX image for nRF52832. I can burn the softdevice into flash with nrjftool.
An...
We have an application where certain executions hold more priority over BLE link. We are implementing a critical section(disable/enable interrupts). However, in some corner...
Hello I've noted some problems when try to use the app_timer in repeat mode with a tick time <= 100ms. I see that the BLE Mesh SDK sets the RTC1.CC[0] compare register in...
I my application, I wish to send a large (60 bytes) bulk of data atomically, i.e. either send all or nothing. Assume I cannot increase the MTU.
Is it possible to query...
Hi
I am using the SDK 15.2.0 and developing for a NRF52832 using Segger.
I have a problem with the define NRF_SAADC_CHANNEL_COUNT in "nrf_saadc.h". It is set to 8. ...
