We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
I am programming a BL652 module (contains an nRF52832 with populated DC/DC inductors). I am programming it through the nRF52 DK in SEGGER studio.
When I run the blank (no...
Hi All,
A very general question here. I understand that using pre-defined services like the battery service help standardize the way peripherals send data to the central...
I'm using JLinkRTTViewer to look at RTT output from my code. The problem is that when I try to go into POWER_OFF, it generates a reset instead.
Is there a way to go into...
hi,
We want to position with aoa(angle of arrival) method, can it provide the One IQ-sample is a pair of in-phase and quadrature-phase samples, and Phase and amplitude information...
Hi,
I am using a nrf52840 development kit flashed with the ICMP example provided in SDK 15 and I am using a device with Bluez tools version 5.47 to connect to it.
However...
While investigating problems I'm experiencing with bootloader_secure I believe I've identified an error in the HCI TX finite state machine ( components/serialization/common...
We have implement a PPI for device match to trigger a GPIO toggle . but now we want to trigger a SW interrupt or a callback function .
my question is how to set PPI TASK...
Hi,
I merged UART exam ple from nrf5 sdk v14.2 with light switch client example from mesh sdk v1.0.1, i have 2 boards client board which is nrf52832 and server board which...
I'm developing an application using the NRF52832. Im using the ADC, and there may be times where the NRF52832 has 0V on its supply pin, but the voltage on the ADC pin is nonzero...
Dear Nordic Support,
does the BLE Uart example (SKD 14.2) inlcude any data link layer machnisms, for example error detection & correction, collision avoidance?
I implemented...
hi to all,
i am developing a ble device with nrf51822 and i encounter with a problem, in my program i have code like below :
in this point program work well, but when...
Hi
I'm facing a problem with light switch demo from mesh SDK v1.0.1, when running the light switch client, as shown in the rtt viewer below the configuration of the server...
My customer is modifying the code based on the example provided in the SDK 15.0.0 to suit their project:
Project file from the SDK under \ nRF5_SDK_15.0.0_a53641a\examples...
Hi,
I am making a project with the nRF52832.
In this project i must configurate another chip with SPI.
The timing must be very accurate. Now the problem is that the...
Hi Team,
I am using nRF52832 to implement smart watch product and it is now close to PP stage.
Currently our product testing engineer found that in a relative noisy environment...
