I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
So im basing my project on your Android-nRF-UART-master example found in github, i don't know if its a app bug or issue regarding the circuit, but first connection is always...
I want to send over Uart when Button1,Button2, Button3 and Button4 are pressed.
static void button1_pressed(void)
{
printf("\r\nButton 1 pressed\r\n"); //Turn on
}...
Hi,
I'm starting to work on nRF52 with eclipse (on Ubuntu). I use this tutorial to configure everything : devzone.nordicsemi.com/.../
Everything looks good but when I try...
Hello,
I am having difficulty having two nRF24L01P's communicate with one another.
I have set up the devices in what I thought was a minimal system.
I will appreciate...
What is the switching frequency of the DC/DC regulator in the nRF52832? The DC/DC is great for reducing power consumption, but I am worried about the switching noise getting...
Hello.
I am trying to save i/o lines on an 8-pin PIC, and planning to run an nRF24L01P with its CE pin tied to VDD. I am willing to power-down to get out of the RX mode...
Hi
I am using an Identive NFC reader/writer SCL3711 and their sample app to read tags.
In the sample app, through the debugger I can see that it is registering an NDEF...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use nrf51422 and integrated BMA250E for Pedometer,
Now I can count the step but I dont how to calculate the speed, cadence and stride length like below
static void...
Hi All,
From my firmware I need to send large ble packets say of 1 K to the phone.
Is there any library or example code for sending large packets. Currently I am splitting...
Hi,
Our application requires that we connect a nRF52832 to a Microchip PIC32MZ host via the Nordic parts UART (RS-232 at CMOS levels).
In a previous application, we...
Hi everyone,
I've been testing SPIM with easyDMA, using nrf_drv_spi. I'd like to flush a 6-axis sensor FIFO in one SPI operation (31 samples * 12 bytes = 372 bytes) but...
Hi,
I am working with the ble_app_uart (central and peripheral) example and they already run fine. Now I discovered that some button actions are already defined on the...
Hello,
I have created the simple software usign NRF51DK to make the led blink for 5 times by using while loop
just to make the other part of my software
my aim of this...
