Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I need a battery-powered programmable device to communicate via Bluetooth to a headset, and communicate with another device via serial (TXD/RXD) interface. Performance requirements...
Hello,
I am writing a single byte value to a cypress module using write with response (BLE_GATT_OP_WRITE_REQ). For some reason the peripheral will receive the value but...
Hi!
I am trying to develop a way for a Bluetooth Central and Bluetooth Peripheral using Secure Connections (security mode 1 level 2 if I'm not mistaken) using a static...
Dear nRF,
I have couple of nRF21540-dk boards (PCA10112) in my hand. I would like to use nRF Connect Direct Test Mode to activate TX and RX.
I found that the tool lacks...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
I am taking over a firmware Bluetooth project and am reading the code that is having some issues. Below is a snippet from a BLE characteristic read callback. Here a double...
I set a timer on the net core of nrf5340. The timer sets an interrupt of 10s. After the chip is reset and runs for 10s, the while (1) of the main function is interrupted,...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
If I add CONFIG_LOG=y to "prj.conf" in the zephyr sample peripheral_dis, when...
Hello,
I'm working with a NRF52840 DK and a module BLE nrf805.
I'm programming thanks to the software SEGGER.
I have sent the blinky simple in my dev kit to test a...
Hello,
I am using the Segger Embeddd Studio from the nRF Connect Desktop and the nRF52840-DK board.
I am working over the project into the "ses" directory for SoftDevice...
Hi,
Do you have an example of the \ble_peripheral\ble_app_hrs with Coded PHY for the nRF5_SDK_17.1.0? I have tried to use the BLE_GAP_PHY_CODED definition in different places...
Hi,
Is it any possible setup to connect a NRF52840-DK to the nRF Connect app in a smartphone without pairing or bonding? That would help me for testing and in this stage...
Hello
I am launching a project and I intend to:
Want to use multiple mobile phones and nrf-mesh software, Connect to a mesh server and turn on or off a led
So I connect...
This commit to the sdk-nrf repo: https://github.com/nrfconnect/sdk-nrf/commit/fdd7a24857a6e762055a0192293fc85165246e7f appears to me to indicate that hardware crypto support...
