hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I would like space in flash that can be written to during production and then never changes or is overwritten. I have explored adding a section in the linker.
Are these...
Hi there...
I am using :
Device :Custom board using nrf52840 (fanstel module BT840)
SDK : nRF5_SDK_17.0.2
SoftDevice : S140 7.2.0
In order to add DFU capability...
Hello,
Any updates on the modem firmware v1.1.3 and v1.3.0 certification status for Verizon? I was told v1.1.3 was supposed to be around Q4 and v1.3.0 was supposed to...
The actual title is too long, the problem is this.
The documentation for s110 says:
Commands to write a buffer to flash
If the SoftDevice is enabled: This call initiates...
Hi All,
I am developing a Zigbee based light controlling product using nrf52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
All functionality and features developed...
Hi,
I run the radio test with our PCBA with SDK17.0.2, but when I want to send "start_tx_modulated_carrier 100", there's no callback response "<info> app: The modulated...
Hi.
I am looking to implement a nRF52840 chip in my 5v battery operated door lock.
Sorry if this is asked before or should be clear from documentation, but I am not...
Hi,
Do you have an example of how to implement a serial console with nrf connect 1.4.99-dev1 with nrf5340_REV1, I tried compiling usb_uart_bridge but got following error...
There are two central sd_* methods for writing to flash - write and erase. The problem is I need to know where I can put my data without trashing something else that is already...
I have two projects exhibiting the same problem.
I have custom board using the nRF52832 and another using the nRF52840. In both cases I am using nRF5 SDK latest version...
Hello,
I would like to have confirmation that the NRF52 will be compatible with my need.
The NRF52 must be able to be connected to a smartphone, while receiving advertising...
I have problems with my custom board.
I developed the firmware with the nrf52832-dk custom and there the firmware runs standalone (with RTT logs on and without) . but now...
I use a nRF52840 Dongle as the Sniffer HW. I use 2 other nRF52840 boards, one is a peripheral (NUS) and the other is a central/peripheral (NUS). The cen/per connects as a...
Hi I have a custom nRF52840 board, and I have a current BLE UART setup. I also want to communicate with a IMU module via serial connection. Can you point me in the direction...
