I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi everyone,
I'm a little bit helpless at the moment, I'm using the function "nrf_drv_spi_transfer" for the SPI communication with a power management chip. This chip is...
I want to save data to NAND Flash Memory (W25M02GV) and extract data to USB MSC. If you have an example of this, I want to get help. The SDK is using 15.2.0. nRF52840 -> QSPI...
Hi Engineer I am using nRF52832 to develop a product. I want to save a flag to flash (FDS) before leaving the factory, and then read this flag every time I turn it on, and...
Dear Community,
I am working on the following application: using the RaspberryPi to flash over-the-air nRF52 nodes (Nordic's Secure DFU BLE bootloader)
For that I have...
Hi all, I have 2 module NRF52832.
Module 1: I using BLE and ESB at the same time, so I request timeslot for ESB, mode RX
Module 2 : I not use BLE, so I can't request timeslot...
Hi,
I added DFU functionality to my Mesh-client application as shown in your DFU-example.
At startup I get this log message:
nrf_mesh_dfu.c, 904, ERROR: No CMD handler...
We have been using the Nordic nRF52840 Preview DK to work with our debugger vendor, iSystem. On page 32 of nRF52840_DK_User_Guide_v1.3.pdf, lists TRACEDATA[1] being connected...
I'm adding the peripheral/RTC project to experimental/CGMS. I cannot seem to get past ASSERT in nrf_rtc_prescaler_set. I changed the prescaler from 4095 to 0xffff as I suspected...
Hello,
I try to build a working firmware for reading some parameters from external sensors and transmit them thru BLE (I am using S130 and SDK 12.3.0). I have already developed...
I am using nRF5_SDK_14.2.0_17b948a on a Fanstel BT832 module which is having nRF52832 SoC. And I am using s132_nrf52_5.1.0_softdevice.hex .
In my application, I need to...
I modified the "ble_app_uart_c" to connect HM-10 (using TI BLE chip CC254x) SPP peripheral.
Ignoring the filtering process (make function adv_uuid_compare(nrf_ble_scan.c...
Downloaded from Git Hub nRF ToolBox from GitHub project dated Nov 12 2018
Tried to build with Android Studio 3.3.2 JRE 1.8.0.152
But get build error
Error C:\users\maltr...
Hi,
I use the nrf52 to connect to a central using BLE 4.0 where power consumption is a sensitive issue. I want to understand how encryption will increase the Link Layer...
I use pc-ble-driver-master/hrc as central to connect the target device which runs with modified ble_app_uart hex.
I can discover service and characteristic correctly, but...
