I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi there!
I'm using nrf9160 DK's SiP to establish TLS connection to MQTT broker.
When I call nrf_inbuilt_key_write it returns 13 error code which means "If the operation...
Hi everyone.
In mesh light switch example., i try to add timer0 (or any timer).
After initialize timer, application always jump to timeout event, and i don't know why...
I am developing based on ble_app_uart example of SDK12 for nRF51 DK and I need to switch BLE off completely when power disappears to save battery and switch back on when power...
After reading the document for nRF52840 Radio Peripheral. I have a doubt about LENGTH field in packet format. what is the difference between LENGTH field and STATIC_PACKET_LENGTH...
Everything works fine if i use the default baudrate
NRF_UARTE_BAUDRATE_115200 but if i change it to 250000 or something higher the applications starts and goes directly...
Hello ,
I want to read around 6 analog pins, not necessarily simultaneously. I could afford some delay in between them. i am using nrf52832 dev kit with sdk 15. How do i...
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.3.0/nrf/gs_programming.html#building-with-ses
I am following the example at the address below.
However, the following...
Hi,
This error has been bugging me for few days and I still have no luck in troubleshooting it.
Recently, I just changed my work project from nrf51822 device to nrf52832...
Hi DevZone members,
I would like to output the elapsed seconds as a floating point value using NRF_LOG_INFO. However, nothing is generated for the floating point value....
I am interfacing nrf52832 with TI TRF7960A using SDK 14.2.0
According to Application Report ( http://www.ti.com/lit/an/sloa140a/sloa140a.pdf) ,
when receive data, SPI...
Stuck at square one I'm afraid - I can't download the nRF5 SDK...
I've tried many times to download the SDK from this link: https://www.nordicsemi.com/Software-and-Tools...
I am trying to flash a hex file with the XIP address offset into the QSPI flash(MX25U25645G) by nrifprog, the memrd command is working since I can read the data that the firmware...
Hello!
I'm trying to add bonding to my DFU. The DFU without bonds works perfectly but when I set #define NRF_DFU_BLE_REQUIRES_BONDS and NRF_SDH_BLE_SERVICE_CHANGED to 1...
Hi ,
I am a begineer to nRF24LE1. I am looking for application notes, books, tutorials on nrf24LE1. I have found some application notes in the documentation they are either...
