dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Is it possible for one Arduino Uno to have a BLE nRF8001 module and a nRF24L01+ module wired to it (allowing each module to communicate simultaneously)? According to the wiring...
We are trying out the new nRF5x SDK v12 and it looks like the previously working ble_app_hids_mouse example is broken now.
It compiles successfully, but as soon as we try...
I have observed that the Radio Notification from ble_radio_notification.c becomes inverted sometimes. I saw this post about the same problem:
devzone.nordicsemi.com/.....
I would like to use nRF5 SDK for IoT with some functionalities (e.g. SEGGER RTT) from nRF52 SDK. Can I just copy desired modules to my SDK for IoT and suppose it'll work?...
Hello,
For some industrial reasons, I need to store the passkey in the flash of the nRF5 during production and retrieve it at run-time.
I would like to know if there...
Hi,
for our prototyp we use a NRF52. When i flash the device, it will always be go in sleep mode after a duration of time and stay in there.
Is there an interrupt which...
Hi all,
i am using V11 sdk.
i want to send data "hello" in beacon application.
how to add that feature.?
any function calls are there?
-Thanks in advance
Hi,
I am using a PIC microcontroller in my project (18F family) and I would like to know which are the tools needed to begin development with the NRF80001.
I already...
Hello,
I am doing a project using nRF51822, s130 and SDK 11. I have modified the example ble_ap_hrs_rscs_relay.
My problem comes when I try to update a notification...
Hi,
I am porting our application from SDK10 nrf51 to SDK12 nrf52. The application takes use of a serial console accessible over UART.
I notice the new logger module...
Hi all,
i am V11 sdk.
Task:
i want to send and receive data without connecting the nordic_uart example
i.e ble_uart eg is send and receiving the data when we press...
Hi all,
i am using V11 SDk,
my task:
One board should broadcast continusuly.
if there is any neighbour is broadcasting ....then that will capture those data too...
Hi,
I am working on adc module of nrf51,through adc i am taking data and storing it in array.now i have to crossexamine this adc data with the prestored data and have to...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS) against the Bluetooth Test Specification (Document Number CPS.TS.1.1.1).
We fail the...
We have been working on a project that requires the following separate segments be programmed to the board:
softdevice hex file
app hex file
UICR hex file
...
