here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello all,
I'm trying to send SPI signal from nRF52-DK to other circuit component.
nRF52 doesn't receive data, and send 16 bit data at one transfer.
I want to send data...
Developing on nrf9160 using NCS 2.1.2 and MFW 1.3.3, is there any sort of Hard Fault detection and handler besides the k_sys_fatal_error_handler hook in lib/fatal_error/fatal_error...
Hello,
I recently ordered a Thingy:53.
The first time I turned it on, I successfully tried the Edge Impulse app, and updated the Thingy:53 network and app firmware via...
Hi, my slave will send 55 bytes to SPIM, if I check slave data when SPIM received all data, and it will spend 1.8ms, I think its long.
Can I check data when SPIM starts...
Dear Nordic team, We are using the nRF connect SDK version 2.1.2. Our prototype uses the nrf52840dk board and the KScan application template. However, when directly trying...
Hi,
Want to update the linker script as below in segger embedded studio? How to add this using flash_placement.xml. //update your linker script (.ld file) to expose information...
I'm trying to use the ADC on the DK52 (PCA100040) to sample and transmit data to a PC. I've been able to write code that samples data to a buffer and I've modified the peripehral...
Dear all,
I've got some problems with the uart implementation in the peripheral uart example. I am using nRF52833 DK and SDK 2.0.2.
What I need for evaluation is a device...
I've the following situation:
1. Send CoAP message trough send(), this causes the the nRF9160 to start RCC connection
2. Wait for RCC connected mode (LTE_LC_RRC_MODE_CONNECTED...
Hello!
I am in the process of adding OTA DFU support to our existing application. However, I'm having problems starting the DFU process.
For security reasons we want to...
Hi there,
We are using the nrf9160 DK with Serial LTE Modem (1.8.0) to run some tests on the modem (1.3.1). We are using the MQTT client AT commands in order to connect...
Good day
I am attempting to use lwm2m to post temperature sensor data. At the moment I'm trying to to initialize object with ID 3300 (generic sensor)but it is not appearing...
MacOSX 13.0.1, Intel. nRF Connect SDK v2.2.0 as downloaded by Toolchain Manager v1.2.1 from nRF Connect for Desktop 3.12.1.
Same happened with SDK v2.1.2.
Similar steps...
Hi,
I was trying to put the nRF5340 Audio DK board in DTM mode to test RF capability but couldn't find out any way to do so.
Please let me know if I can find some documentation...
