Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I attend the introduction course for the nRF's, and I am at Lession 3. The task is to print 'Hello World' to the device, using Serial Port and COMx. I have made the...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
Hi ,
I am working on thingy53 and using ncs 1.9.1 I need to enable the BMI270 sensor and need the acceleration and gyroscope data from it. So for that, I primary using the...
Hello,
I am using the provisioner example to provision and configure all my sensor nodes in my project. My use case consists of around 60 sensor nodes. While provisioning...
Hi,
I moved my code on a second windows pc, checkout the code from git,download the same nordic sdk and softdevice version, same SES version but running on my board, the...
Devices: nrf52840 peripheral to nrf52833 central
background: We switched the mode from BLE_GAP_PHY_1MBPS, to BLE_GAP_PHY_CODED. The content of the advertisement data was...
Hello,
I want to use standalone logging for each file (/module)(/driver) of my program, therefore register different logging modules with different log levels each. Registering...
Hi,
I am attempting to configure a nRF52840 (packaged as Seeeduino XIAO Sense) for the popular printer software Klipper.
i have the following processor options and am...
Hello I'm trying to use GPIO pins as UART on the nRF 52 DK rather than the default UART pins. How do I change the pin configuration? I'm using nRF SDK version 17.1. 0
I now have two dk's, one as a master and the other as a slave. The slave sends data to the master, and the master forwards the data to the PC. That is, the piece of dk that...
We are seeing an issue with Android 13 on Samsung phones connecting to our device over BLE. After CONNECT_IND the phone will attempt to send a LL_FEATURE_REQ. It takes about...
Above is the code that im using.
Module - BT832x
Debugger - Segger J-link
IDE - Segger IDE
SDK - nRF5_SDK_17.0.2_d674dde (Downloaded from nordic website)
Program...
Hello Nordic Team,
I am facing an issue in my project that uses BLE and FreeRTOS. If I call nrf_sdh_enable_request () in main() before starting the task scheduler vTaskStartScheduler...
Hi,
I use 2 nrf52840 custom board, one is use a peripheral sensor with a lot of services and the other is used as a central with bt_shell_command.
Now i need to be able...
