hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi we are in the preproduction phase and we see that in the market there are two order codes NRF9160-SICA-B1A-R and NRF9160-SICA-R.
Looking at the datasheet it looks like...
Hi there,
I am trying to obtain a .hex file for my project for Release Configuration. I don't see the .hex file get updated in the pca10040\s132\ses\Output\Release\Exe directory...
I am a electrical engineering student in my final year of study and am developing a product for my final year dissertation.
The project idea is to help identify sickness...
Hello,
I am using,
iPhone 7
iOS v14.8.1
nRF Connect for Mobile iOS v2.4.13
I have used nRF Connect for Mobile on android which shows this menu when peripheral...
I am using the NRF52840-DK and using the Zigbee light bulb example.
1. The DK board successfully connects to the zigbee network - Z2M in this case.
2. I have added an...
Hi everyone, my colleague developed a firmware using Arduino Nano 33 BLE and PlatformIO. Now I have to rewrite the code using Segger Embedded Studio. The problem is in the...
Hi there, I am developing a peripheral to central system with nrf52840 base on NUS service. Now I tried to increase the MTU of the peripheral to 247 to increase the transfer...
Hi,
I am using NCS for development and configuring GPIO pin as input, but I found the GPIO can't configuring as NO-PULL mode. There are only two options: Pull up and Pull...
Hi,
I am working on ble_bms_app template. While the nrf52840dk is connected to laptop, I don't get JLINK connected notification on the desktop. Sometimes i get the connected...
Hello.
I'm using nrf52832 (S132 v7.0.1, SDK v17.0.0) to develop peripheral roles.
Setting UUIDs for advertisements, services, and characteristics. At that time, sd_ble_uuid_vs_add...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
