Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
I'm getting an undefined reference to "app_uart_init". I've enabled the respective libraries in the sdk_config.h:
//====================================================...
I tried to combine the Wireless_uart example with the USB CDC example to be capable of using both but it doesn't seem to be working.
When I plug my board using the nrf USB...
Hi there,
I am using WIN10, Segger studio 4.52c and nRF SDK16.
I can successfully run ble_app_uart example on PCA10056, but when i try to run same code on fanstel EV-840...
Hi, I have been working on setting up the environment for development of nrf52840 and nrf9160 the past three days. I have nRF9160 dk which comes with nrf52840. I have been...
When I built and run your example Bluetooth: Peripheral HIDS keyboard and I saw the following errors in logs: E: set-value failure. key: bt/ccc/283926aaa86c0 error(-2) E:...
Hi,
We would like to know whether below gang programmer can be used for gang firmware flashing of NRF9160 application FW and NRF9160 modem FW.
Also we would like to know...
I am getting the following error when trying to register a nRF9160-DK with a HWID. There was an error adding your device: nRFCode 40001:
Please advise how to move forward...
Hello!
I've got a couple of NRF52832 based modules - Holyiot-17095-nRF52832. These modules are presented in the list of supported - https://www.nordicsemi.com/Software-and...
I performed below mentioned steps:
Downloaded SDK 12.1.0
Soft Device s130_nrf51_2.0.1_softdevice.hex
Built secure boot-loader with new public key
Built project ble_app_hrs...
I'm trying to compile hci_usb sample of Zephyr with Nordic Connect SDK v1.3.0 using Nordic's proprietary controller but apparently it fails.
I'm using following configuration...
Hi I'm doing the Bluetooth GATT: How to Design Custom Services & Characteristics [MIDI device use case] example ( https://www.novelbits.io/bluetooth-gatt-services-characteristics...
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer. My setup: HW: PCA10040 1.2.4 SDK: 15.3 Project: \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral...
Hi
I'm using SKD16.0.0 and S132, and I want to realize that peripherals can only connect to a center with a known MAC address through directed advertising. How should I...
Hi Folks,
I am getting in trouble with SoftDevice activation. Indeed, my application did not return from the "nrf_sdh_enable_request()" call, more precisely it hangs into...
Hello,
I am currently working on BT840 and BT832 modules and trying to run the sample codes which are given by Nordic (specifically ble_app_uart which runs with UART service...
