I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I have seen that the nRF52840 PS v1.0 specifies the RSSI_PERIOD to be 15us. I have also seen that the nRF52832 has only a RSSI_PERIOD of 0.25us (PS v1.3+) or 8us...
I need some technical information:
- the micro Host can (through a pin?) make WakeUp of the BLE module to configure it / change the operating parameters etc? - the BLE module...
While visiting the Nordic Tech Tour we were discussing the pros and cons of BLE Mesh with a Nordic employee. He recommended that we also looked at a different solution, a...
This is essentially a repeat of :
https://devzone.nordicsemi.com/f/nordic-q-a/38808/is-a-3-bit-synchronous-3-data-lines-clock-parallel-input-at-16-368-mhz-feasible
Instead...
Hi,
I am using Keiluvision 5 , nRF5-SDK version - 15.2 with SoftDevice S140, My application requires to have NFC functionality as well as UART, but when I try to merge the...
Hi. need help with dynamic routing. I have a 9 node mesh running Thread and so far i have collected and analyzed latency data and packet delivery ratio data. I need to find...
Hello there,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hi Nordic,
I plan to use the newest SDK (because the ATT MTU > 23 is need) for NRF52832 to develop a PC tool to connect with Nordic BLE peripheral devices, and then send...
Hi, i am using SDK15.0.0 with nrf52840 chip.
I am interfacing a SPI device in the SPIM0. The SPIM module looks working fine without a softdevice.
But when i integrate...
SDK - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Hi,
I am using an android phone to write a 32 byte array to the nrf52 device which...
nRF51_SDK_10.0.0\examples\ant\ant_plus\ant_bsc\bsc_tx\combined\button\pca10028
ANT BSC Speed event time not change After a period of work although button press or relea...
Hi. I am a beginner with nrf52832. Trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
I have problem with both custom boards and DEV board.
From a certain time after GPIO direction bit seems not effecting the pins.
To get rid of software factor, I all erase...
Hello,
I'm currently using nrf8001 to sent a 20-byte packet. It works fine and my phone application receives the right data. However, when I send another packet that has...
Hi,
I try to create program which will save same data on SD card, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it...
