Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
We are developing a device which should have a power save mode where no BLE connection is possible (switch off the BLE to a minimum power consumption) and restart the...
Hi, there~~ Just noticed that there are codes for the Android nRF connect.
github.com/.../Android-nRF-Connect
Using that code, I wish to create my personal sniffer that...
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
Hi,Support Team
I Use the nRF51822 SOC for SDK12.3-example-DFU-bootloader_secure, when I Select the ZIP upadate file,it has a reminder "Loading file has failed. Try different...
Hi,
I use buttonless DFU with the secure bootloader.
When I push a button my application advertise in fast mode with an interval of 40ms and for 5s. After it return to...
SEGGER Embedded Studio Release 3.40 Build 2018052200.36079
The so-called "flash (sic?) placement" XML file contains two sections:
First:
which does, indeed, seem...
Hello, I am currently working on a nr52840 s140 Sdk 15.0 card and I want to recover data from a component running on the i²c bus. (I have not yet installed the component on...
Hello,
I would like to know if it is possible to use a nRF52840 as bridge between ethernet and 802.15.4/thread. For a sensor network I need an ip connection between multiple...
Hi,
I'm using nRF52 DK. I was checking the message sent by NRF_LOG_INFO() on Termite. I'm getting driver error when I try to connect to laptop's bluetooth.
Without the...
Hello
what is the maximum limit for PWM outputs pins on nrf52832? Can we use all the GPIO pins as a PWM output?
For ADC, i can see there are 8 dedicated pins , but i...
hello i am beginner in this,i am using example\ peripherals\ saadc for nrf 52832. This example code is done by using timer and i could not understand how to use timer. We...
hi all ,
i now need porting nrf_libuarte_async lib for my project . it show some error
How to deal with this problem？
i reference (experimental_libuarte project...
