Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi.
I am working on a custom nRF52810 board (SDK 2.7.0).
When connecting LIS2DH12 via SPI in the .dts file, I see an error -->
.dts code -->
prj.conf -->
Please...
I try to capture the broadcast packets from the broadcast_audio_source application to investigate the BASE (which holds the configuration of BIGs, subgroups and streams)....
Hi DevZone Team,
I hope this message finds you well. I am reaching out to seek your assistance regarding the HID mouse implementation we are working on using the Nordic...
The question concerns using the nrf fuel gauge library for a setup with an nPM1300 PMIC and an NRF52840, implemented using the nRF5_SDK_17.1.0. Is it possible?
Even with the LTK key entered, wireshark cannot decode Bluetooth packets between two paired connected devices I followed this course exactly,but it failed to live up to expectations...
NRFX_TWIS_EVT_GENERAL_ERROR
I am thinking of implementing TWI slave functionality in the nRF52840.
The event handler is written as follows.
Read operations from...
I am thinking of using nRF52832 as both transmitter and receiver, and creating a firmware where the transmitter adds the acquired data to the Manufacturer Specific Data of...
Hi Nordic：
SDK version: NCS_V2.7.0
sample： peripheral_uart
config：
Compile error without any changes：
May I ask how to solve this problem？
best regards！
jermi...
Hello,
I get the error message in red when pressing Connect below:
The certificate is downloaded as instructed in the devacademy 4.2.
server_certificate.crt: ...
Hi,
I recently purchased a Thingy91, and here's what I’ve done so far:
Built the firmware
Registered the SIM and device on the cloud platform
Built the Asset Tracker...
I found a related post ( ) where the advice was given to just get a DevKit, which I agree with for development, but my understanding is the nRF52 dongle firmware contains...
MCU : nrf52840
SDK : sdk_17.1.0
Hello, we are developing a product using the nRF52840.
However, we have observed that while the nrf_log_backend_uart~ function is operating...
Dear Nordic support,
I've done some testing to send many data in BLE notifications, and I have a question regarding the BLE stack implementation. We are using NCS v2.6.1...
Hi,
I combined the throughput example and the lbs example in NCS v2.6.2 running in NRF5340DK. It seems the advertisement is not resuming after i disconnect the app (NRF...
